NHT CS-6.3 Ci, CS-6.1 Ci specifications „ Parts List each speaker, „ Tools Needed

Page 2

CS-6.3 Ci is going to serve as rear (surround) channels in a home theater system, make sure to install them toward the “rear” of the room (the opposite side from where the television will likely be). If you wish to get an idea how they will look, try taping the supplied cutout templates to the ceiling.

„Parts List (each speaker):

“Speaker” pack includes:

(1) Bezel with driver

(1) Metal grille

(2) Absorptive foam pads

(1) paint shield - cutout template

“Mounting Bracket” pack includes:

(1) Mounting bracket

(2) Mounting wings

(4) 5 x 50mm flathead screws

„Tools Needed:

#2 Philips screwdriver Pencil

Tape measure

Utility knife or keyhole saw Level

Wire strippers Safety goggles Protective gloves

Tech Tips: Pre-Wiring for New Construction

1.For best results, avoid running speaker cable near electrical wire, as it may induce a 60Hz hum in the audio signal. It’s a good idea to run the speaker cable after the electrical wiring has already been completed, so that you can route the speaker cable at least three feet away from the electrical wiring. If speaker cable and electrical wiring must run parallel, install the cable within a metal conduit. Note that low-voltage wiring (doorbell, intercom, telephone, security, etc.) are unlikely to induce hum and can typically be run parallel to speaker cable with no detrimental effects.

2.When drilling holes through wall studs or ceiling joists, use a drill bit that is at least as wide as the speaker cable that will be routed through them. Always drill through the center of the stud or joist. If the hole must be drilled within one inch of the edge of a wall stud, add a nail plate to the drywall side to protect the cable from possible nails and screws put in the wall later. Line up the holes in the studs or joists as you go, so that pulling the cable through them will be easier.

fig.2

fig.1

Page 1 Page 3
Image 2
Page 1 Page 3
Contents NHT-9993 „ Placement„ Design „ Tools Needed „ Parts List each speakerTech Tips Pre-Wiring for New Construction „ Installation New Construction unfinished ceilings Tech Tips Optimizing Sonic Performance „ Connections „ Maintenance„ Painting „ OperationCS-6.1 Ci and CS-6.3 Ci Getty Court Benicia, CA NHT-9993To Obtain Service Limited Warranty Valid Only in the U.S.AWarranty Period What’s Not Covered CS-6.3 Ci Tech Tips PlacementCS-6.1 Ci

CS-6.1 Ci, CS-6.3 Ci specifications

NHT, a well-known name in the audio industry, has developed the CS-6.1 Ci and CS-6.3 Ci, two exceptional loudspeakers that are designed to deliver high-quality sound performance for audiophiles and casual listeners alike. These models exhibit a blend of advanced technology, elegant design, and impressive features, making them ideal for home theater systems or stereo setups.

The CS-6.1 Ci is a compact bookshelf speaker that strikes a balance between size and audio excellence. It features a 6.5-inch woofer and a 1-inch silk dome tweeter, which work harmoniously to produce a broad frequency range with crystal-clear highs and powerful lows. The CS-6.3 Ci, on the other hand, is a floor-standing speaker that enhances the listening experience with its dual 6.5-inch woofers. This configuration allows the CS-6.3 Ci to achieve a deeper and more impactful bass response, making it a perfect choice for those who crave a more immersive audio experience.

One of the standout characteristics of both models is their use of advanced crossover technology. The speakers come equipped with precision-engineered crossovers that ensure a seamless transition between the woofer and tweeter, thus minimizing distortion and maximizing clarity. This results in a coherent soundstage, where every instrument and vocal is accurately represented, allowing listeners to fully appreciate their favorite music or movie soundtracks.

Another notable feature is the cabinet design. NHT has crafted the CS-6.1 Ci and CS-6.3 Ci with high-quality materials that not only enhance durability but also reduce resonance. The sleek finish and understated aesthetic allow these speakers to blend seamlessly into any decor while making a subtle statement about audio sophistication.

In terms of connectivity, both models are designed with standard binding posts, providing compatibility with a wide range of audio systems. Their sensitivity ratings make them versatile, allowing them to be paired with various amplifiers without compromising sound quality.

Overall, the NHT CS-6.1 Ci and CS-6.3 Ci speakers embody a commitment to high-performance audio. With their innovative technologies, quality construction, and remarkable sound reproduction capabilities, these models cater to the needs of serious listeners who appreciate the fine nuances of music and audio storytelling. Whether used in a home theater setup or as part of a dedicated stereo system, they are sure to elevate the listening experience to new heights.
Top Page Image Contents