Yard-Man 573 Maintaining Your Lawn Mower, Handle Height, Carburetor, Cutting Height, Lubrication

Page 10

SECTION 6: MAKING ADJUSTMENTS

WARNING: Do not at any time make any adjustment to your lawn mower without first stopping the engine and disconnecting the spark plug wire.

Handle Height

Your mower is shipped with the handle in the higher height position.To lower the handle height for your convenience, proceed as follows.

Lower

 

Handle

Notch

 

Figure 8

•Remove the starter rope from the rope guide.

•Remove the upper handle by removing the hand knobs and carriage bolts. Lay the upper handle out of the way, being careful not to bend or kink cables.

•Remove the hairpin clips from the weld pins on the handle brackets. Press outward on the legs of the lower handle, and remove it from the mower.

•Turn the lower handle around so the notches on the bottom of the lower handle are facing forward as shown in Figure 8. Reassemble, placing the bottom holes in the handle over the weld pins in the handle mounting bracket.

•Reassemble the upper handle.

•Place the hairpin clips in the inner holes in the weld pins. Reattach the starter rope.

Carburetor

Minor carburetor adjustments may be required to compensate for differences in fuel, temperature, altitude and load. To adjust carburetor, refer to the engine manual.

NOTE: A dirty air cleaner will cause an engine to run rough. Make sure air cleaner is clean and attached to the carburetor before adjusting carburetor.

WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts and heated surfaces (e.g. muffler).

Cutting Height

An adjusting plate and thumb lever at each wheel position provides cutting height adjustment. Each adjusting plate has nine height positions. Height of cut will be changed when the thumb lever is moved from one hole to another.

•Simply depress the lever towards wheel and move wheel and lever assembly to desired position. All wheels must be placed in the same relative position. See Figure 9.

Height

Adjustment

Lever

Figure 9

SECTION 7: MAINTAINING YOUR LAWN MOWER

WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of maintenance work on lawn mower.

Lubrication

Blade Control

•Lubricate the pivot points on the blade control handle and the brake cable at least once a season

with light oil. See Figure 10. The blade control must operate freely in both directions.

Wheels

•Lubricate the wheel bearings (if so equipped) at least once a season with light oil (or engine oil). Also, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil. See Figure 10.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual MTD LLC, P.O. BOX 361131 CLEVELAND, OhioTable of Contents Important Safe Operation Practices General OperationSlope Operation ServiceChildren Do NotGeneral Service Your ResponsibilitySlope Gauge Assembling Your Lawn Mower Know Your Lawn Mower Converting to Side DischargeOperating Your Lawn Mower Carburetor Maintaining Your Lawn MowerHandle Height Cutting HeightCutting Deck Cutting BladeEngine OFF-SEASON Storage Trouble Shooting Guide Parts List for Model Model MANUFACTURER’S Limited Warranty for MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone

573 specifications

The Yard-Man 573 lawnmower is a remarkable piece of outdoor equipment that offers both power and efficiency for homeowners seeking a dependable tool for maintaining their lawns. With its robust design and thoughtful engineering, the Yard-Man 573 stands out in the crowded market of residential lawn maintenance.

One of the key features of the Yard-Man 573 is its reliable engine. Equipped with a durable gas engine, it delivers ample horsepower to handle various grass types and challenging terrains. This engine ensures consistent performance, even under demanding conditions, allowing users to tackle their mowing tasks with confidence.

The Yard-Man 573 boasts a wide cutting deck, typically around 21 inches, which enhances its ability to cover more ground in less time. This size not only speeds up the mowing process but also provides a clean and even cut. The cutting height can be easily adjusted to cater to different grass lengths and seasonal changes, giving users the flexibility to maintain their lawn as per their preference.

User comfort and convenience are also prioritized in the design of the Yard-Man 573. It features an ergonomic handle that is adjustable, allowing users of different heights to operate the mower comfortably. The foldable handle mechanism makes storage a breeze, saving space in the garage or shed.

Another technological advancement integrated into the Yard-Man 573 is its efficient grass collection system. The mower is equipped with a rear bagger, which effectively collects clippings, minimizing the cleanup effort after mowing. This feature not only helps keep the lawn tidy but also allows for easy disposal of clippings, whether for composting or waste collection.

Safety is a critical aspect of lawnmowers, and the Yard-Man 573 does not disappoint. It is designed with safety features such as a blade brake that stops the blades when the user releases the handle, preventing accidents. Additionally, the mower's sturdy build and reliable materials contribute to longevity and resilience.

In summary, the Yard-Man 573 combines power, efficiency, and user-friendly features to create a lawnmower that meets the demands of both seasoned landscapers and first-time homeowners alike. With its advanced engineering and thoughtful design, it is poised to provide a reliable solution for maintaining a beautiful lawn year after year.
Top Page Image Contents