Yard-Man 247.27432 manual Side to Side, Seat Adjustment, Steering Adjustment, Front to Rear

Page 15
Side to Side

Side to Side

If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as follows:

WARNING: Turn the tractor’s engine off, remove the key from the ignition switch and apply the tractor’s parking brake before making any adjustments to the cutting deck.

With the tractor parked on a firm, level surface, place the lift lever in the top notch (highest position) and rotate the both blades so that they are perpendicular with the tractor.

Measure the distance from the outside of the left blade tip to the ground and the distance from the outside of the right blade tip to the ground. Both measurements taken should be equal. If they’re not, proceed to the next step.

Loosen, but do NOT remove, the hex cap screw on the left deck hanger bracket. See Figure 8B.

Balance the deck so that both blade tip measurements taken earlier are equal.

Retighten the hex cap screw on the left deck hanger bracket when proper adjustment is achieved.

A

Deck Front to Rear

Stabilizer

Bracket

Deck

Front to Rear

Lock Nuts

Jam Nuts

B

Hex Cap Screw

Deck Hanger Bracket

Side to Side

Figure 8

SEAT ADJUSTMENT

To adjust the position of the seat, move the seat adjustment lever (located under the seat) to the left and slide the seat forward or backwards. See Figure

9.Make sure seat is locked into one of the six adjustment positions before operating the tractor.

SEAT ADJUSTMENT Seat

Seat Adjustment Lever

Figure 9

STEERING ADJUSTMENT

If the tractor turns tighter in one direction than the other, or if the ball joints are being replaced due to damage or wear, the steering drag links may need to be adjusted.

Hex Nut and

Zerk Fittting

 

Pivot Bar

(if so equipped)

 

Lock Washer

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Axle

Drag Link

Ball Joint

Jam Nut

Figure 10

15

Image 15
Contents AutoDrive Lawn Tractor Models IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLYMTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO OPERATOR’S MANUALMTD PRODUCTS INC SECTION 1 TABLE OF CONTENTSSECTION 2 FINDING YOUR MODEL NUMBER SECTION 3 CALLING CUSTOMER SUPPORT1. GENERAL OPERATION SECTION 4 IMPORTANT SAFE OPERATION PRACTICES3. CHILDREN 4. SERVICE2. SLOPE OPERATION DO NOTFigure 1 Safety Labels found on your unit Slope Gauge SECTION 6 TRACTOR SET-UP SECTION 5 ATTACHMENTS & ACCESSORIESATTACHING THE BATTERY CABLES INSTALLING THE MULCH KITSECTION 7 CONTROLS CHOKE CONTROL IGNITION SWITCHINDICATOR MONITOR / HOUR METER THROTTLE CONTROL LEVERPARKING BRAKE BUTTON ELECTRIC PTO POWER TAKE-OFF KNOBLIFT LEVER AUTODRIVE PEDALCRUISE CONTROL BUTTON SEAT ADJUSTMENT LEVERSAFETY INTERLOCK SWITCHES SECTION 8 OPERATIONSTOPPING THE ENGINE SETTING THE CUTTING HEIGHTSETTING THE CRUISE CONTROL STARTING THE ENGINEOPERATING THE HEADLIGHTS USING THE LIFT LEVERENGAGING THE ELECTRIC PTO POWER TAKE-OFF KNOB DRIVING ON SLOPESFront to Rear SECTION 9 ADJUSTMENTSMOWING LEVELING THE DECKFront to Rear SEAT ADJUSTMENTSTEERING ADJUSTMENT Side to SideBRAKE ADJUSTMENT CARBURETOR ADJUSTMENTCUTTING DECK REMOVAL SECTION 10 MAINTENANCECLEANING THE ENGINE AND DECK ENGINE42-inch decks CHANGING THE DECK BELTS46-inch decks CHANGING THE TRANSMISSION DRIVE BELTSFront of Tractor Upper Drive BeltLower Drive Belt Reassemble by following the above steps in reverse order CUTTING BLADES BATTERYPIVOT POINTS SECTION 11 LUBRICATIONTIRES FUSECorrective Action SECTION 12 TROUBLESHOOTING GUIDETrouble PossiblePage Model Fuel Cap For Two Gallon Tank, Shown Ignition KeyElectrical System/Tractor Body Model Lift Assembly 3126 Plastic Flange w/ Fitting Not Shown Steering AssemblyModel Drive System Model Power Take-off System 42-inch Deck 46-inch DeckSpindle Assembly, 5.75 Dia Cutting DecksIntek Twin Briggs & StrattonKohler Single-cylinderEngine Accessories Other Warranties MANUFACTURER’S LIMITED WARRANTY FOR