Yard-Man 437 manual Assembling Your Lawn Mower

Page 7

SECTION 3: ASSEMBLING YOUR LAWN MOWER

Removing Unit From Carton

•Remove staples, break glue on top flaps or cut tape at carton end and peel top flap to open carton.

•Remove loose parts if included with unit.

•Cut corners and lay carton down flat. Remove packing material.

•Roll or slide unit out of carton. Check carton thoroughly for loose parts.

NOTE: Make sure not to crimp cables while removing the loose parts or the entire unit from the carton.

Hardware Pack

 

 

Please identify each piece

 

 

of the hardware pack as

Wing

Carriage

shown here.

Nut

Bolt

 

 

1/4-20 (2)

1/4-20 (2)

Tools Required

•Pair of Pliers

•Funnel

NOTE: Reference to right or left hand side of the mower is observed from the operating position.

Disconnecting Spark Plug

•Before setting up your lawn mower, disconnect the spark plug wire from the spark plug, and ground it to retaining post on the engine. See Figure 1.

Figure 1

Assembling Handle

•For shipping purposes, the grass bag was placed on top of the unit. Remove it from the unit and set it out of the way. See Figure 2 .

Figure 2

•Raise the lower handle, as shown in Figure 2 , until it snaps into place.

•Raise the upper handle as shown in Figure 2 .

•Tighten the two wing nuts which are already on the handle. See Figure 3 .

 

Tighten these

 

wing nuts

 

Lower

Upper

Handle

Handle

 

Figure 3

NOTE: Make sure to route the cables outside the lower handle. Also do not crimp the cables while lifting the handle up.

•Remove the hairpin clips from the outer hole in the weld pins on the handle bracket assemblies. Using a pair of pliers, squeeze one leg of the lower handle against the handle bracket assemblies. Insert the hairpin clip into the inner hole on the weld pin. Repeat on other side. See Figure 4.

•After you have moved the hairpin clip, install the carriage bolt, (carriage bolt must go to the inside of handle) included in the hardware pack, in the upper hole on the handle mounting bracket. Secure with one plastic wing nut, also included in the hardware pack. See Figure 4.Repeat process on other side.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesDo Not ServiceChildren Slope OperationYour Responsibility General ServiceSlope Gauge Assembling Your Lawn Mower Assembling Grass Catcher Attaching Starter RopeAttaching Grass Catcher Blade Control Handle Know Your Lawn MowerRemoving Grass Catcher Converting to Side-DischargeStarting Engine Operating Your Lawn MowerGas and Oil Fill-Up Before Starting MowerBagging Grass Clippings Using the MulcherAdjusting Cutting Height Operating Your Lawn MowerEngine Maintenance Cleaning the Lawn MowerMaintaining Your Lawn Mower Blade Care Servicing Your MowerTo Sharpen Blade Replacing Rear Flap Making AdjustmentsAdjusting Handle Height Adjusting CarburetorGasoline TROUBLE-SHOOTING GuideMower Parts List for Model Model MTD LLC, P.O. BOX 361131 CLEVELAND, Ohio 44136-0019 Phone MANUFACTURER’S Limited Warranty for

437 specifications

The Yard-Man 437 is a creative solution for homeowners seeking to enhance their outdoor maintenance experience. With its rugged design and powerful performance, it stands out as a reliable tool for tackling various yard tasks. The model boasts a compact size, making it easy to maneuver around tight spaces, while still providing ample cutting power required for efficient lawn care.

One of the main features of the Yard-Man 437 is its robust engine. Equipped with a reliable four-stroke engine, it ensures not only robust performance but also lower emissions, contributing to a cleaner environment. This engine delivers impressive torque, allowing the Yard-Man 437 to handle thick grass and challenging terrain effortlessly.

Another notable characteristic of the Yard-Man 437 is its cutting system. It comes outfitted with a wide cutting deck that can be adjusted for different grass heights. The deck’s sturdy construction can handle rough use while maintaining precision in cutting. Additionally, the model incorporates mulching capabilities, enabling homeowners to recycle grass clippings back into the lawn, promoting healthier soil and reducing waste.

For user convenience, Yard-Man has integrated several modern technologies into the 437. It features an easy-start system that allows for quick ignition, saving precious time on busy mornings. The model also utilizes a self-propelling mechanism, which significantly reduces the physical exertion required during operation, especially on slopes or uneven ground.

The cutting height can be easily modified with just a simple lever adjustment, allowing users to customize their mowing to suit varying grass types and conditions. Moreover, the 437 is designed with comfort in mind. It has an ergonomic handle that provides a comfortable grip and minimizes vibration, enhancing the overall mowing experience.

Durability is another important aspect of the Yard-Man 437. Built with high-quality materials, it is designed to withstand the rigors of regular lawn maintenance. Coupled with its maintenance-friendly design, which allows for easy access to engine components, this model ensures longevity and reliability in performance.

In summary, the Yard-Man 437 is an excellent choice for those seeking a powerful, efficient, and user-friendly lawn mower. Its combination of a robust engine, advanced cutting system, ease of use features, and durable construction make it a standout model in the realm of outdoor power equipment. Whether for small yards or larger properties, the Yard-Man 437 proves itself capable and reliable, delivering optimal results with every use.
Top Page Image Contents