Specifications, Select Thermostat Location

SPECIFICATIONS

ELECTRICAL DATA	Shipping Temperature Range:
Electrical Rating:	-40°F to 150°F
17 to 30v AC 50/60 Hz.
0.05 to 1.5 Amps	APPLICATIONS
1.5 Amps Maximum Total Load (All terminals	For use with:
combined)	• Standard heat/cool, heat-only, or cool-only systems
	•	Three-wire zone valve systems
Anticipation:	•	Millivolt systems
Heating 2 to 40	•	Electric heat systems
Cooling 4 to 40 }Reference Values	•	Gas or oil fired systems
	•	Gas systems with intermittent ignition devices
THERMAL DATA		(I.I.D.) and/or vent dampers
Setpoint Temperature Range:	Do not use with:
40° F to 99°F (4°C to 37° C)	•	Multi-stage systems
Operating Ambient Temperature Range:	• Heat pump systems
32°F to 105°F	• Systems exceeding 30v AC and 1.5 Amps
Operating Humidity Range:	ACCESSORIES
0 to 90% RH (non-condensing)	Remote Sense Kit W. R. Part No. F145-1049
	Thermostat Guard W. R. Part No. F29-0198 (clear) or
	F29-0238 (opaque)

INSTALLATION

NEW INSTALLATION

You should program the thermostat with batteries installed before attaching on subbase. See OPERA- TION GUIDE for programming instructions.

SELECT THERMOSTAT LOCATION

Proper location insures that the thermostat will provide a comfortable building temperature. Observe the following general rules when selecting a location:

1.Locate thermostat about 5 ft. above the floor.

2.Install thermostat on a partitioning wall, not on an outside wall.

3.Never expose thermostat to direct light from lamps, sun, fireplaces or any temperature radiating equip- ment.

4.Avoid locations close to windows, adjoining outside walls, or doors that lead outside.

5.Avoid locations close to air registers or in the direct path of air from them.

6.Make sure there are no pipes or duct work in that part of the wall chosen for the thermostat location.

7.Never locate thermostat in a room that normally warmer or cooler than the rest of the building.

8.Avoid locations with poor air circulation, such as behind doors or in alcoves.

ROUTE WIRES TO LOCATION

NOTE

All wiring must conform with local and national electrical codes and ordinances.

1.Probe for obstructions in partition before drilling 1/2" hole in wall at selected location. Take up quarter round and drill a small guide hole for sighting (see Fig. 1). From basement, drill 3/4" hole in partition floor next to guide hole. In basementless buildings, drill 1/2" hole through ceiling and into partition from above.

2.Through this hole drop a light chain, or 6" chain attached to a strong cord. Snag cord in basement with hooked wire. In basementless buildings, drop cord through hole in ceiling and down partitioning; snag cord at the thermostat location.

3.Attach thermostat wire to cord and pull wire through hole in wall so that 6" of wire protrudes.

1/2" HOLE FOR

THERMOSTAT WIRE

STOUT CORD WITH 6"

CHAIN ATTACHED

APPROXIMATELY

BASEBOARD5 FEET

STRIP MOLDING

1/4" GUIDE HOLE

FOR SIGHTING

QUARTER ROUND

REMOVED

3/4" HOLE IN FLOOR OF PARTITION

HOOKED WIRE FOR SNAGGING CHAIN

Figure 1. Routing Thermostat Wires

1F97W-71 specifications

The White Rodgers 1F97W-71 is a highly versatile and advanced digital thermostat designed to enhance heating and cooling systems in residential environments. This unit stands out for its blend of modern technology, user-friendly features, and energy efficiency, making it a popular choice among homeowners looking to optimize their indoor climate control.

One of the main features of the 1F97W-71 is its large, easy-to-read touchscreen display. The intuitive interface allows users to effortlessly navigate through settings, making adjustments to temperature and scheduling straightforward. The thermostat provides precise temperature control, ensuring that your home stays comfortable while reducing energy consumption.

This model is equipped with a 7-day programmable schedule, giving users complete control over their heating and cooling patterns. Homeowners can set different temperature settings for each day of the week, allowing for personalized comfort based on their schedules. This feature not only enhances comfort but also contributes to energy savings, as it can automatically reduce heating or cooling when the home is unoccupied.

The 1F97W-71 also incorporates advanced technologies, such as Smart Recovery, which learns how long it takes to reach your desired temperature and starts the heating or cooling process in advance to ensure that your home is at the right temperature at the scheduled times. The thermostat is compatible with various heating and cooling systems, including multi-stage systems, heat pumps, and conventional HVAC setups.

Another notable characteristic of the White Rodgers 1F97W-71 is its Wi-Fi capability. This allows users to remotely access and control their thermostat via a smartphone app, offering the convenience of making adjustments on-the-go. With the app, users can monitor energy usage, receive alerts, and even access weather forecasts to make informed decisions about their home climate.

Energy efficiency is a cornerstone of the 1F97W-71's design. It has ENERGY STAR certification, indicating that it meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency. This certification not only helps contribute to a more sustainable environment but can also lead to significant savings on energy bills over time.

In conclusion, the White Rodgers 1F97W-71 is a feature-rich digital thermostat that combines user-friendly controls, advanced technology, and energy efficiency to provide an optimal home climate solution. Its programmable scheduling, Wi-Fi connectivity, and compatibility with various HVAC systems make it a standout choice for homeowners seeking to enhance their comfort while managing energy costs.

SPECIFICATIONS

ELECTRICAL DATA

APPLICATIONS

1.5 Amps Maximum Total Load (All terminals

Anticipation:

THERMAL DATA

ACCESSORIES