Stiga PRO SVAN, PRO 25 manual Belt transmissions, Battery

ENENGLISH

4.Check that the rubber gasket (21:H) at the bot- tom of the filter is intact.

5.Install the new filter and the spring in the sleeve. Insert the filter until it snaps into place in the sleeve.

6.Reinstall the unit in the tank. The upper section of the filter must click securely into the recess in the upper section of the tank.

5.6.4 Filling

1.Check that the gaskets on the 4 drainage plugs are intact. See fig. 22. Reinstall the plugs. Tight- ening torque: 15-17 Nm.

2.Only applies to Pro20, Pro25 and Pro Svan: Moisten the new filter’s gasket with oil and in- stall the filter. See fig. 16:A.

3.Fill the oil reservoir with the new oil.

4.Check that the clutch release lever (6:R) is in the outer position (drive position).

If the engine is to be run indoors, an ex- haust extraction device must be con- nected to the engine’s exhaust pipe.

5.Prepare a suitable vessel with the new oil.

NOTE! The oil is sucked into the system very quickly. The reservoir must always be kept topped up. Under no circumstances may air be sucked in.

6.Fill the oil reservoir with new oil.

7.Start the engine and allow it to idle. Gradually top up the oil in the reservoir so that the level constantly reaches the mark.

8.Reinstall the oil filler cap and close the engine casing.

9.Reset the drive shafts’ valves in accordance with fig. 25.

10.Drive the machine 8-10 metres forwards and 8- 10 metres backwards. If the machine has hy- draulic power assisted steering, apply full steer- ing lock at the same time.

11.If the machine has a hydraulic implement lifter, raise and lower the lifter 3-4 times.

12.Adjust the oil level in the reservoir.

5.7 Belt transmissions

After 5 hours of operation, check that all the belts are intact and undamaged.

5.8 Steering

The steering must be checked/adjusted after 5 hours of operation and thereafter after 100 hours of operation.

5.8.1 Checks

Briefly turn the steering wheel back and forth. There must be no mechanical clearance in the steering chains.

5.8.2 Adjustment

Adjust the steering chains if required as follows:

1.Put the machine in the straight-ahead position.

2.Adjust the steering chains with the two nuts, lo- cated under the central point. See fig. 29.

3.Adjust both nuts by the same amount until there is no clearance.

4.Test drive the machine straight forwards and check that the steering wheel is not off centre.

5.If the steering wheel is off centre, undo one nut and tighten the other.

Do not over-tighten the steering chains. This will cause the steering to become heavy and will in- crease wear on the steering chains.

5.9Battery

If acid comes into contact with the eyes or skin, this can cause serious injuries. If any part of the body has come into contact with acid, rinse immediately with copious amounts of water and seek medical assistance as soon as possible.

The battery is a valve-regulated battery with 12 V nominal voltage. The battery fluid does not need to and cannot be checked or topped up. The only maintenance that is required is charging, for exam- ple after extended storage.

The battery must be fully charged be- fore being used for the first time. The battery must always be stored fully charged. If the battery is stored while discharged, serious damage will occur.

5.9.1 Charging with the engine

The battery can be charged using the engine’s gen- erator as follows:

1.Install the battery in the machine as shown be- low.

2.Place the machine outdoors or install an extrac- tion device for the exhaust fumes.

3.Start the engine according to the instructions in the user guide.

4.Allow the engine to run continuously for 45 minutes.

5.Stop the engine. The battery will now be fully charged.

5.9.2 Charging using battery charger

When charging using a battery charger, a battery charger with constant voltage must be used. Contact your dealer to purchase a battery charger with constant voltage.

The battery can be damaged if a standard type battery charger is used.

72