Shindaiwa T242, X7502800900 manual 99922201033, Manufacturers Warranty Coverage

Page 23

ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT

FOR ECHO AND SHINDAIWA BRANDS

The Environmental Protection Agency (EPA) and the California Air Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/ SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffl er, fuel tank, fuel feed lines, fuel cap assembly, spark plug, air fi lters, and other associated components. Where a warrantable condition exists, ECHO Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended to the original owner including all subsequent owners.

MANUFACTURER'S WARRANTY COVERAGE:

The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.

OWNER'S WARRANTY RESPONSIBILITIES:

As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance or unapproved modifi cations.

You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986- 7783, web site WWW.SHINDAIWA.COM.

WHAT DOES THIS WARRANTY COVER?

ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is purchased by an end user.

HOW WILL A COVERED PART BE CORRECTED?

If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.

WHAT PARTS ARE COVERED?

Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired or replaced part will be warranted for the remaining ECHO Inc. warranty period.

Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.

Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the fi rst scheduled replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the fi rst scheduled replacement point for that part.

Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts, and must be provided without charge if the part is still under warranty.

Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the manufacturer.

Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts suffi cient to meet the expected demand for such parts.

SPECIFIC EMISSION RELATED WARRANTED PARTS:

 

• Electronic Ignition System

• Spark Plug

• Catalytic Converter / Muffl er Assembly

• Carburetor (complete assembly or replaceable components)

• Choke

• Fuel-Injection Assembly (or replaceable components)

• Fuel Tank

• Fuel Cap Assembly

• Air Filter

• Fuel Feed Line (and associated clamps/connectors as applicable)

WHAT IS NOT COVERED?

Any failure caused by abuse, neglect, improper maintenance, unapproved modifi cations, use of unapproved add-on parts/modifi ed parts or unapproved accessories.

This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.

99922201033

 

01/2010

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents T242 Trimmer Introduction ContentsMinimize the Risk of Fire Safety InstructionsWork Safely Stay AlertProperly Equipped Operator Safety LabelsBe Aware of the Working Environment Product DescriptionEmission Control Exhaust & Evaporative SpecificationsFront handle installation Assembly and AdjustmentsPrior to Assembly Adjust Throttle Lever Free PlayTrimmer Head Install the Trimmer Head AssemblyInstall the Cutting Attachment Shield T242 Examples of 501 mixing quantities Mixing FuelAfter use Filling the fuel tankMixing Instructions Starting the Engine Starting a Flooded Engine When the Engine StartsStopping the Engine Checking Unit ConditionEngine Operating Speeds MaintenanceGeneral maintenance Cutting Grass-Units equipped with a trimmer headSpark Plug Daily MaintenanceHour Maintenance MufflerRemove and replace Filter element 10/15-Hour MaintenanceHigh Altitude Operation Carburetor AdjustmentEngine Break-In Long Term Storage Adjusting Engine IdleIdle Speed Adjustment Troubleshooting Guide Engine is knocking Engine stops abruptly Poor accelerationExceptions 99922201031 06/2010 Purchased Repair Parts and Accessories99922201033 Manufacturers Warranty CoverageParts/Serial Number Servicing Information

X7502800900, T242 specifications

The Shindaiwa T242 is a powerful and reliable trimmer designed for both professional landscapers and homeowners seeking an efficient tool for their yard maintenance needs. With its robust engine and advanced features, the T242 stands out in the competitive outdoor power equipment market.

One of the main features of the Shindaiwa T242 is its 21.2 cc, two-stroke engine, which delivers impressive power and efficiency. The engine is designed to reduce emissions, adhering to environmental regulations while still providing sufficient torque for cutting through thick grass and dense vegetation. The lightweight design of the trimmer allows for extended use without causing excessive fatigue, making it ideal for both small and large landscaping tasks.

Another notable characteristic of the T242 is its Easy Start system, which simplifies the starting process. This technology reduces the amount of effort needed to start the engine, enabling users to get to work quickly without the frustration that often comes with pull-start engines. The trimmer also features a high-capacity fuel tank that allows for longer operation times between refueling, further enhancing productivity.

The Shindaiwa T242 is equipped with a commercially rated, dual-line bump feed head, providing users with the ability to easily advance the line by tapping it against the ground. This feature is particularly useful for users who need to maintain their trimmer without having to stop and manually feed the line. The cutting width of 17 inches makes it versatile enough for both trimming around tight areas and clearing larger sections of grass.

Durability is another strong suit of the T242, as it is constructed with high-quality materials that are built to withstand tough conditions. The trimmer’s design includes vibration-dampening technology, which minimizes user fatigue and allows for greater control while operating the machine.

In addition, the T242 features an ergonomic handle design that provides optimal comfort and grip, ensuring that users can operate the trimmer for extended periods without discomfort. The adjustable handle allows users to customize their grip position based on their height and preference, further enhancing the overall user experience.

In conclusion, the Shindaiwa T242 trimmer combines power, efficiency, and user-friendly features in a lightweight and durable package. It is an excellent choice for anyone looking to tackle landscaping tasks with ease and confidence, making it a valuable addition to any outdoor equipment arsenal.
Top Page Image Contents