Shindaiwa T261/EVC, T261X/EVC, 81605 manual General Maintenance, Daily Maintenance, Hour Maintenance

Page 13

General Maintenance

IMPORTANT!

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY SHINDAIWA CORPORATION THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WARRANTY CLAIM.

WARNING!

Before performing any maintenance, repair or

cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintnenance work.

WARNING!

Non-standard parts may not operate properly with

your unit and may cause damage and lead to personal injury.

NOTE:

Using non-standard replacement parts could invalidate your Shindaiwa warranty.

Muffler

This unit must never be operated with a faulty or missing spark arrester or muf- fler. Make sure the muffler is well secured and in good condition. A worn or dam- aged muffler is a fire hazard and may also cause hearing loss.

Spark Plug

Keep the spark plug and wire connections tight and clean.

Fasteners

Make sure nuts, bolts, and screws (except carburetor adjusting screws)

are tight.

Blades

Keep blades sharp and check blade condition frequently. If a blade’s per- formance changes suddenly, stop the engine and check the blade for cracks or other damage. Replace a damaged blade

IMMEDIATELY!

WARNING!

nNever repair a damaged blade by welding, straightening, or by modifying its shape. An altered blade may break during operation, resulting in serious personal injury.

nDO NOT use 2-tooth or NON- Shindaiwa approved 4-tooth cut- ting blades on Shindaiwa trimmers or brushcutters.

nBlades are not interchangeable between Shindaiwa edgers and trimmer/brushcutter models.

Operating any unit with a blade or attachment not approved for that unit can be hazardous and may cause serious injury.

Daily Maintenance

Prior to each work day, perform the following:

nRemove dirt or debris from the engine, check the cooling fins and air cleaner for clogging and clean them as neces- sary.

nCarefully remove any accumulation of dirt or debris from the muffler or the fuel tank. Dirt build-up in these areas could cause the engine overheating, induce premature wear, or create a fire hazard.

nCheck for loose or missing screws or components. Make sure the cutting attachment is securely fastened.

nCheck the entire unit for leaking fuel or grease.

10-Hour Maintenance

Every 10 hours of operation (more frequently in dusty or dirty conditions): Remove the air cleaner element.

See Figure 28. Clean or replace as neces- sary. To clean element: wash it thoroughly in soap and water. Let it

dry before reinstalling the element.

CAUTION!

Do not operate the unit if the air cleaner or element is damaged, or if the element is wet.

Remove and clean

or replace

the

element

 

Unscrew

 

Fastener

26129

 

Figure 28

 

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Part Number 81605 Rev /06 T261/EVC Trimmer T261X/EVC TrimmerIntroduction ContentsWork Safely General Safety Instructions The Properly Equipped OperatorStay Alert Minimize the Risk FireBe Aware of the Working Environment Safety LabelsProduct Description SpecificationsAdjust Throttle Lever Free Play Assembly and AdjustmentsPrior to Assembly HandleAssembly Trimmer Head Assembly Cutting Attachment ShieldInstall the Cutting Attachment Shield Install the Trimmer HeadNever operate the T261X without the safety clip in place Assembly Blade T261XMount the Cutting Blade Filling the Fuel Tank Mixing FuelStarting the Engine Examples of 501 mixing quantitiesCutting attachment may rotate when the engine is started Adjusting Engine IdleWhen the Engine Starts Idle Speed AdjustmentShoulder Strap Checking Unit ConditionCutting Grass-Units Equipped with a Trimmer Head Blade Thrust Using a Blade T261XBrushcutter Handlebar Brushcutter Shoulder StrapDaily Maintenance General MaintenanceHour Maintenance Every 50 hours of operation 10/15-Hour MaintenanceLong Term Storage Hour MaintenaceBlade Sharpening Shindaiwa Tornado BladeEngine does not Start Troubleshooting GuideLOW Power Output Additional Problems Emission System Warranty Statement Fax 503 Telephone 81-82-849-2481 Telephono 6696-692 2481-849-82-81 FaxJapan 3167,-731 Hiroshima Ku-Asaminami NishiEmisión de Sistema del Garantía de Declaración 18SP Continuación Diagnóstico GuíaRemedio 17SP16SP Diagnóstico GuíaPlazo Largo de Almacenamiento Discos de AfiladoHoras-135 Cada Mantenimiento Múltiples Dientes de DiscosHoras-10/15 cada Mantenimiento Horas-50 Cada MantenimientoMotor del internas Partes las a suciedad o polvo entreDiario Mantenimiento Horas-10 Cada MantenimientoGeneral Mantenimiento Verticales Cortes T261X disco un UsandoDesmalezadora Para Hombro de Correa Desmalezadora Para Bicicleta Tipo MangoArnés de Correa Corte de Cabezal con Equipadas Máquinas Césped de CorteUnidad la de Condición la Verifique Motor del Parada Motor del Mínima Marcha de AjusteContinuación Motor del Arranque Motor el arranca CuandoCombustible de Tanque el Llenando Motor del ArranqueCombustible de Mezcla IncendiosCorte de Cuchilla la Monte T261X Disco/Cuchilla EnsamblajeCorte de accesorio del Protector Ensamblaje Corte de Cabezal EnsamblajeMango Acelerador del holgura la AjusteAjustes y Ensamblaje Ensamblar de AntesProducto del Descripción EspecificacionesPíes Seguridad de EtiquetasTrabajo de Area del Alerta Esté Motor del cerca fuegos encienda ni fume Nunca n Juicio Buen UseIncendios de Riesgo El Disminuya ¡ADVERTENCIA Alerta MantengaseSeguridad De Declationes Introducción Contenido11/06 .Rev 81605 Parte De Numero Shindaiwa Propietario/Operador Del ManualDvertencia¡A
Top Page Image Contents