Shindaiwa 81605, T261X/EVC, T261/EVC manual Assembly Blade T261X, Mount the Cutting Blade

Page 8

Assembly: Blade T261X

Mount the Cutting Blade.

Turn the T261X upside down so the gearcase output shaft is facing UP and remove the shaft bolt, bolt guard and holder B from the gearcase shaft.

1.Align the hole in blade holder A with the matching hole in the gearcase flange and then temporarily lock the output shaft by inserting a hex wrench through both holes. See Figure 12.

2.Slide the safety clip off-center. See Figure 13.

3.Fit the blade over the safety clip and then center it over the flange on holder A. See Figure 14.

CAUTION!

Install the blade so its printed sur- face is visible to the operator when the brushcutter is in the normal operating position.

WARNING!

Shaft Bolt

Bolt Guard

Holder B

Gear Shaft

Safety Clip

Holder A

26109

Hex Wrench

Figure 12

Slide the safety clip off-center

Output

Shaft

Safety

Clip

Figure 13

23110

Slip the Saw Blade In	Center the Safety
Place	Clip
26111
Figure 14	26112
Figure 14

The blade must fit flat against the holder flange.

The blade mounting hole must be centered over the raised boss on blade holder A.

NOTE:

When installing certain blades, it may be nec- essary to temporarily remove the safety clip.

4.Lock the blade in place by centering the safety clip on the output shaft. See Figure 14.

WARNING!

Never operate the T261X without the safety clip in place!

Output

Blade Shaft

	23113
Blade Holder B	Hex Wrench
	Hex Wrench

Tighten the assembly (blade

not shown for clarity)

IMPORTANT!

Figure 15

23115

The machined recess in holder B must completely surround the safety clip, and both holders must be flat against the surface of the blade.

5.Install blade holder B on the output shaft. See Figure 15. The recess in the holder must completely cover the safety clip, and must fit tightly against the blade.

6.Install the bolt guard and then the blade retaining bolt. Using the combi- nation spark plug wrench/screwdriver, tighten the bolt firmly in a counter- clockwise direction.

7.Remove the hex wrench.

The T261X should now be completely assembled and ready for use with a blade.

Image 8

Contents T261/EVC Trimmer T261X/EVC Trimmer Part Number 81605 Rev /06Contents IntroductionGeneral Safety Instructions The Properly Equipped Operator Work SafelyStay Alert Minimize the Risk FireSafety Labels Be Aware of the Working Environment Specifications Product DescriptionAssembly and Adjustments Adjust Throttle Lever Free PlayPrior to Assembly HandleAssembly Cutting Attachment Shield Assembly Trimmer HeadInstall the Cutting Attachment Shield Install the Trimmer HeadMount the Cutting Blade Assembly Blade T261XNever operate the T261X without the safety clip in place Mixing Fuel Filling the Fuel TankStarting the Engine Examples of 501 mixing quantitiesAdjusting Engine Idle Cutting attachment may rotate when the engine is startedWhen the Engine Starts Idle Speed AdjustmentCutting Grass-Units Equipped with a Trimmer Head Checking Unit ConditionShoulder Strap Using a Blade T261X Blade ThrustBrushcutter Handlebar Brushcutter Shoulder StrapHour Maintenance General MaintenanceDaily Maintenance 10/15-Hour Maintenance Every 50 hours of operationHour Maintenace Long Term StorageBlade Sharpening Shindaiwa Tornado BladeTroubleshooting Guide Engine does not StartLOW Power Output Additional Problems Emission System Warranty Statement Fax 503 Telephone 81-82-849-2481 2481-849-82-81 Fax Telephono 6696-692Japan 3167,-731 Hiroshima Ku-Asaminami NishiEmisión de Sistema del Garantía de Declaración Continuación Diagnóstico Guía 18SP17SP RemedioDiagnóstico Guía 16SPDiscos de Afilado Plazo Largo de AlmacenamientoHoras-135 Cada Mantenimiento Múltiples Dientes de DiscosHoras-50 Cada Mantenimiento Horas-10/15 cada MantenimientoMotor del internas Partes las a suciedad o polvo entreGeneral Mantenimiento Horas-10 Cada MantenimientoDiario Mantenimiento T261X disco un Usando Verticales CortesDesmalezadora Para Hombro de Correa Desmalezadora Para Bicicleta Tipo MangoUnidad la de Condición la Verifique Corte de Cabezal con Equipadas Máquinas Césped de CorteArnés de Correa Motor del Mínima Marcha de Ajuste Motor del ParadaContinuación Motor del Arranque Motor el arranca CuandoMotor del Arranque Combustible de Tanque el LlenandoCombustible de Mezcla IncendiosT261X Disco/Cuchilla Ensamblaje Corte de Cuchilla la MonteCorte de Cabezal Ensamblaje Corte de accesorio del Protector EnsamblajeAcelerador del holgura la Ajuste MangoAjustes y Ensamblaje Ensamblar de AntesEspecificaciones Producto del DescripciónTrabajo de Area del Alerta Esté Seguridad de EtiquetasPíes Juicio Buen Use Motor del cerca fuegos encienda ni fume Nunca nIncendios de Riesgo El Disminuya ¡ADVERTENCIA Alerta MantengaseContenido Seguridad De Declationes IntroducciónDvertencia¡A Shindaiwa Propietario/Operador Del Manual11/06 .Rev 81605 Parte De Numero