MAINTENANCE
Sharpening the Chain
When the cutting edges of the blade become dull, they can be re- sharpened with a few strokes of a file.
In order to keep the blade in balance, all cutting edges must be sharpened equally.
In addition, inspect the chain for correct adjustment (more frequently with a new chain). The chain should feel snug but still pull freely. See Figure 36. Refer to page 16 for adjustment procedures.
Sharpening Instructions (Fig.37)
IMPORTANT!
File all cutters to the same angle and depth! Unequal filing may cause the saw to vibrate or cut erratically!
1.Using a 4.5 mm round file, sharpen all cutters to a 30° angle. Make sure that one fifth (20%) of the file’s diameter is always held above the cutter’s top plate.
NOTE:
For consistent filing angles, use a filing guide such as Oregon® p/n 31692 or equivalent.
2.After all cutters are sharpened, use a depth gauge joiner (Oregon® p/n 106738 or equivalent) to measure the height of each depth gauge.
3.As required, lower the depth gauges to a height of 0.020 inch. Use a flat file; (Oregon® p/n 12211 or equivalent).
4.After all depth gauges have been adjusted, use a flat file to round each depth gauge leading edge to its original curvature and angle.
Figure 36 |
Using a filing
gauge
Using a depth
gauge joiner
Using a flat file to round the front corner on a depth gauge
Figure 37
P231 Specifications
Dry Weight | 6.1 kg/13.4 lb. |
Length w/10" bar | |
assembly | 2804 mm/110.4 in. |
Engine Type | |
Bore x Stroke ... | 32 x 28 mm/1.3 x 1.1 in. |
Displacement ......... 22.5 cc/1.4 cu. in.
Maximum Output .......... 0.8kW/1.1 hp
@ 7500 rpm
Fuel/oil ratio ...... 50:1 with
or JASO FC class
Shindaiwa ONE is a registered JASO FC classified oil and also meets or exceeds
Fuel Tank Capacity | .... 670 ml/22.7 oz. | |
Carburetor Type | Walbro | |
Ignition | ||
Spark Plug | Champion CJ8 | |
Air Filter | ||
filter element |
| |
Muffler Type | ||
Starting Method | Recoil | |
Cooling System | ..................... | Forced air |
Stopping Method | Slide switch |
Transmission Type | .............. | Automatic, | |
centrifugal clutch with bevel gear | |||
Chain Guide Bar | 3/8" pitch, | ||
.043" gauge, | |||
Chain Type | 3/8" pitch Micro Lite™, | ||
.043" gauge |
|
|
|
Sprockets | |||
Gearcase Ratio | ........................... | 1.06 : 1 | |
Chain Speed | 23.5 m (77 ft.)/sec. | ||
@ 10,000 rpm |
| ||
Chain Lubrication | Automatic | ||
adjustable oiler |
|
| |
Chain Lubricant ... Shindaiwa Premium | |||
Bar and Chain Oil |
| ||
Standard Equipment | Bar/chain |
scabbard, tool kit containing a spark plug wrench, 4 mm hex wrench and 8 mm x 10 mm spanner
Optional Equipment | .... Shoulder strap, |
loop handle |
|
Optional Bars | |
EPA Emission |
|
Compliance Period* | ........... Category A |
*The EPA emission compliance referred to on the emission compliance label located on the engine, indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category C = 50 hours (Moderate), B = 125 hours (Intermediate) and A = 300 hours (Extended).
Specifications are subject to change without notice.
DESCRIPTION
28 | 9 |