Servis-Rhino FM60/72 manual Driveline Attachment to Tractor, Cutting Height Adjustment

Page 77

OPERATION

DRIVELINE ATTACHMENT TO TRACTOR

1.Grab and twist black collar on end of attaching yoke toward cutter.

2.Slide yoke (with collar displaced) onto PTO shaft.

3.Move yoke back and forth until locking collar clicks and locks the yoke in place.

WARNING When attaching PTO yoke to tractor PTO shaft, it is important that spring activated locking collar rotates freely and is seated in groove on PTO shaft.

WARNING Be sure PTO shielding and all other shielding is installed and is in good condition.

IMPORTANT: When raising cutter to transport height, be sure there is clearance between the cutter and driveline. Damage will result if driveline hits cutter deck.

CUTTING HEIGHT ADJUSTMENT

WARNING Avoid personal injury! Be sure tractor engine is off, key is removed, and ALLOW BLADES TO STOP TURNING before dismounting to make adjustments.

Important: Avoid very low cutting heights. Striking the ground with blades gives the most damaging shock loads a cutter can encounter and will cause damage to cutter and drive.

1.Using the tractor, raise the mower off the ground and support under it with secure blocking so not to let the mower drift down during maintenance.

2.Holding wheel and yoke assembly up, remove quick-lock pin from top of gauge wheel spindle. Position full length spacers and half spacer as required. All spacers on top of spindle tube allows for approximately 1" cutting height. Adjustments range form 1" to a maximum of 4-1/2" in 1/2" increments.

3.Adjust the length of tractor top links, so that when lifting the mower the front will raise 1"- 2" inches before rear gauge wheels leave the ground. This will allow the flexible hitch to pivot and allow the mower to follow the contour on uneven ground.

STARTING & STOPPING CUTTER

Power for operating cutter is supplied from tractor PTO. Refer to your tractor manual instructions for engaging and disengaging the PTO. Always engage the PTO at low engine rpm. Always operate at recommended PTO speed of 540 RPM. Learn how to stop tractor and cutter quickly in case of an emergency.

IMPORTANT: Stop cutter and tractor immediately upon striking an obstruction. Inspect the cutter and repair any damage before resuming operation. Do not disengage PTO when engine is a full PTO RPM. Always idle engine before disengaging PTO.

WARNING Avoid personal injury. When attempting to stop a tractor which does not have live PTO, the momentum created by the blade carrier of a rotary cutter can cause the tractor to be pushed forward. DO NOT operate this cutter unless tractor has live or independent PTO.

FM6072 08/01

Operation Section 4-3

© 2004 Alamo Group Inc.

 

OPERATION

Image 77
Contents FM60/72 To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Safety ¡LEA EL Instructivo PeligroDo not mount the Tractor while the tractor is Following rules Drugs or alcohol. SG-27 FM6072 08/01 Wait a minute...Save a life Stop Mowing if Passersbyare Within 100 Yards Unless See Your SERVIS-RHINO Dealer Parts InformationQTY Level Description InformationNot Shown See Inside Front Cover of Manual D103 Safety Safety Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Frame Attachment Exceed Horsepower Recommendations Dealer SET-UP Instructions2ND Extended Position Casterwheelattachments ST Extended PositionDischarge Chute Installation Operation Section Attaching Mower to Tractor Lift Type Tractor PreparationStarting & Stopping Cutter Cutting Height AdjustmentDriveline Attachment to Tractor Rear Discharge Models Cutting SpeedCutting Tips Before Operating or Transporting this Mower Driveline Length Check ProcedureDetaching and Storing Front Gauge Wheel Interference Check Driveline LengthStreaking Problem Possible Cause RemedyDamaged Belt Maintenance Section Description Frequency Lubrication InformationLubrication Fitting Location Gauge Wheel Assemblies GearboxBlade Spindle Lubrication Driveline LubricationBlade Servicing Blade InstallationBlade Sharpening Blade RemovalMaintenance Proper Torque for Fasteners StorageBlade Spindle Service Instructions Figure SERVIS-RHINO Page To the OWNER/OPERATOR/DEALER FM60/72-SOM-08/01 00761717C Printed U.S.A RHINO-SERVIS SERVIS-RHINOWARRANTY Registration Information Page Dealer Copy Page Customer Copy

FM60/72 specifications

The Servis-Rhino FM60/72 is a robust and versatile rotary mower designed primarily for commercial and agricultural applications. This machine is built to handle a variety of mowing tasks, making it an ideal choice for municipalities, schools, parks, and large property owners who require reliable performance.

One of the standout features of the FM60/72 is its durable construction. It is equipped with a heavy-duty frame that provides stability and longevity, allowing it to withstand harsh mowing conditions. The mower is available in two cutting widths: 60 inches and 72 inches, offering flexibility depending on the user’s mowing needs. This capability enables operators to cover more ground in less time, making it a cost-effective choice for large areas.

The FM60/72 employs advanced rotary cutting technology, which includes a series of high-quality, heat-treated blades. These blades are designed to deliver a clean cut, promoting healthier grass growth and reducing the risk of lawn disease. The mower’s cutting height is easily adjustable, providing operators with the ability to customize the cut to their specific preferences or requirements.

Another notable feature of the FM60/72 is its user-friendly design. The mower is equipped with a simple-to-use control interface, allowing operators to make adjustments quickly and efficiently while in the field. Its low-profile design enhances visibility and maneuverability, particularly in tighter spaces, making it easier for users to navigate around obstacles.

The Servis-Rhino FM60/72 also prioritizes safety, incorporating features such as a safety shield around the blades and a quick-stop system. These safety measures are designed to protect the operator and bystanders, ensuring peace of mind during operation.

In terms of maintenance, the FM60/72 is engineered for easy servicing. Its design allows for straightforward access to critical components, ensuring that routine checks and maintenance tasks can be performed with minimal downtime. This feature is particularly beneficial for users who rely on the mower for daily operations.

The versatility, durability, and user-friendly design of the Servis-Rhino FM60/72 make it an excellent choice for those in need of a reliable mowing solution. With its wide range of features and advanced technologies, this mower stands out as a top contender in the commercial mowing market, promising to deliver outstanding results and efficiency to its users.