Servis-Rhino FM60/72 manual Cutting Speed, Cutting Tips, Rear Discharge Models

Page 78

OPERATION

OPERATION

To commence operation, reduce engine speed and engage the tractor PTO. Before starting to cut, gradually increase engine speed to develop full PTO speed.

Enter the area to cut with the cutter operating at PTO speed and, if it becomes necessary to temporarily regulate engine speed during operations, increase or decrease the throttle gradually.

To transport, disengage the PTO, raise full transport height.

CUTTING SPEED

Proper ground speed for cutting will depend upon the height, type, and density of material to be cut.

Normally, ground speed will range from 1-1/2 to 3 mph. Tall dense material should be cut at low speed while thin medium height material can be cut at a faster ground speed.

CUTTING TIPS

Always operate PTO at recommended RPM when cutting. This is necessary to maintain proper blade speed and to produce a clean cut.

Under certain conditions, tractor tires may roll some grasses down and prevent them from being cut at the same height as the surrounding area. When this occurs, reduce the tractor ground speed, but maintain PTO RPM. The lower speed will permit grasses to be at least partially rebound and be cut. Taking a partial cut and/or reversing the direction of travel may also produce a cleaner cut.

As often as possible, stop mowing when other people are passing by. Although the Mower is shielded to prevent objects from being thrown out by the blades, no one shield device is 100% effective. The operator has greater knowledge of the dangers of being around this Mower while it is operational than the person on the street.

WARNING Avoid personal injury. Pick up all rocks and other debris before cutting. Enter new areas carefully. Cut material higher the first time to allow cutter to clear unseen objects. Never assume an area is clear. Always check.

Extremely tall grass should be cut twice. Raise cutter and cut twice the desired height. Cut the second time at desired height at 90 degrees to first pass.

Remember, sharp blades produce cleaner cuts and use less power.

Before cutting, analyze the area to determine the best cutting procedure. Consider the height and type of material and the terrain type: hilly, level or rough.

Grass is best cut when it is dry. Mowing wet grass can cause plugging resulting in grass clumps behind the mower.

Grass should be mowed frequently as shorter clippings deteriorate faster.

FIGURE 1

SIDE DISCHARGE MODELS

The grass is discharged to the left. To keep clippings off streets and sidewalks, mow two to four passes counterclockwise, throwing the clippings into the unmowed grass area. Then, complete the job by mowing clockwise and spreading the clippings uniformly over the al- ready-mowed area. FIGURE 1.

REAR DISCHARGE MODELS

The grass is discharged to the rear and slightly to the right. To keep clippings off to streets and sidewalks mow two to three passes clockwise as shown in Figure 1A.

FM6072 08/01

Operation Section 4-4

© 2004 Alamo Group Inc.

 

Page 77 Page 79
Image 78
Page 77 Page 79
Contents FM60/72 To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Safety Peligro ¡LEA EL InstructivoDo not mount the Tractor while the tractor is Following rules Drugs or alcohol. SG-27 FM6072 08/01 Wait a minute...Save a life Stop Mowing if Passersbyare Within 100 Yards Unless Parts Information See Your SERVIS-RHINO DealerInformation QTY Level DescriptionNot Shown See Inside Front Cover of Manual D103 Safety Safety Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Exceed Horsepower Recommendations Dealer SET-UP Instructions Frame AttachmentST Extended Position 2ND Extended Position CasterwheelattachmentsDischarge Chute Installation Operation Section Tractor Preparation Attaching Mower to Tractor Lift TypeCutting Height Adjustment Driveline Attachment to TractorStarting & Stopping Cutter Cutting Speed Cutting TipsRear Discharge Models Driveline Length Check Procedure Detaching and StoringBefore Operating or Transporting this Mower Driveline Length Front Gauge Wheel Interference CheckProblem Possible Cause Remedy StreakingDamaged Belt Maintenance Section Lubrication Information Lubrication Fitting LocationDescription Frequency Gearbox Gauge Wheel AssembliesDriveline Lubrication Blade Spindle LubricationBlade Sharpening Blade InstallationBlade Servicing Blade RemovalMaintenance Storage Proper Torque for FastenersBlade Spindle Service Instructions Figure SERVIS-RHINO Page To the OWNER/OPERATOR/DEALER FM60/72-SOM-08/01 00761717C Printed U.S.A RHINO-SERVIS SERVIS-RHINOWARRANTY Registration Information Page Dealer Copy Page Customer Copy

FM60/72 specifications

The Servis-Rhino FM60/72 is a robust and versatile rotary mower designed primarily for commercial and agricultural applications. This machine is built to handle a variety of mowing tasks, making it an ideal choice for municipalities, schools, parks, and large property owners who require reliable performance.

One of the standout features of the FM60/72 is its durable construction. It is equipped with a heavy-duty frame that provides stability and longevity, allowing it to withstand harsh mowing conditions. The mower is available in two cutting widths: 60 inches and 72 inches, offering flexibility depending on the user’s mowing needs. This capability enables operators to cover more ground in less time, making it a cost-effective choice for large areas.

The FM60/72 employs advanced rotary cutting technology, which includes a series of high-quality, heat-treated blades. These blades are designed to deliver a clean cut, promoting healthier grass growth and reducing the risk of lawn disease. The mower’s cutting height is easily adjustable, providing operators with the ability to customize the cut to their specific preferences or requirements.

Another notable feature of the FM60/72 is its user-friendly design. The mower is equipped with a simple-to-use control interface, allowing operators to make adjustments quickly and efficiently while in the field. Its low-profile design enhances visibility and maneuverability, particularly in tighter spaces, making it easier for users to navigate around obstacles.

The Servis-Rhino FM60/72 also prioritizes safety, incorporating features such as a safety shield around the blades and a quick-stop system. These safety measures are designed to protect the operator and bystanders, ensuring peace of mind during operation.

In terms of maintenance, the FM60/72 is engineered for easy servicing. Its design allows for straightforward access to critical components, ensuring that routine checks and maintenance tasks can be performed with minimal downtime. This feature is particularly beneficial for users who rely on the mower for daily operations.

The versatility, durability, and user-friendly design of the Servis-Rhino FM60/72 make it an excellent choice for those in need of a reliable mowing solution. With its wide range of features and advanced technologies, this mower stands out as a top contender in the commercial mowing market, promising to deliver outstanding results and efficiency to its users.
Top Page Image Contents