Servis-Rhino FM84 manual Blade Servicing, Blade Sharpening, Blade Removal, Blade Installation

Page 87

MAINTENANCE

BLADE SERVICING

Inspect blades before each use to determine that they are properly installed and in good condition. Replace any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be ground out when sharpening.

Use only original equipment blades on this cutter. They are made of special heat-treated alloy steel. Substitute blades may not meet specification and may fail in a hazardous manner that could cause injury.

BLADE SHARPENING

Always sharpen both cutting edges of each blade at the same time, the same amount, to maintain balance. Follow original sharpening pattern as shown. Do not sharpen blade to a razor edge, but leave a 1/32" blunt edge. Do not sharpen back side of blade. Figure 6.

WARNING! Avoid personal injury. Always block the cutter up to prevent it from falling when the blades and/ or carrier are being serviced.

MAINTAINCORNER

FOLLOW ORIGINAL PATTERN

1/32"

FIGURE 6

BLADE REMOVAL

Hold the end of blade using heavy leather gloves and remove left hand threaded bolt.

BLADE INSTALLATION

Install washer on blade bolt and insert bolt into blade. Thread bolt into spindle shaft. NOTE: Blade bolt has left hand threads. Tighten blade bolt to 150 ft. lbs. torque. Use heavy leather gloves during tightening process to hold blade and wrench.

FM84 08/01

Maintenance Section 5-5

© 2004 Alamo Group Inc.

 

MAINTENANCE

Image 87
Contents FM84 To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Peligro ¡LEA ELInstructivo Safety Skin, have the injury treated immediately by a physician Following rules SG-23 Safety Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life See Your SERVIS-RHINO Dealer Parts InformationQTY Level Description Safety Decal LocationSafety Decals FM84 FM84 08/01 Safety Section Alamo Group Inc Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Frame Attachment Exceed Horsepower Recommendations Dealer SET-UP Instructions2ND Extended Position Casterwheelattachments ST Extended PositionDriveline Attachment To Gearbox Operation Section Attaching Mower to Tractor Lift Type Tractor PreparationCutting Height Adjustment Driveline Attachment to TractorStarting & Stopping Cutter Cutting Speed Cutting TipsRear Discharge Models Driveline Length Check Procedure Detaching and StoringBefore Operating or Transporting this Mower Front Gauge Wheel Interference Check Driveline LengthStreaking Problem Possible Cause RemedyDamaged Belt Maintenance Section Lubrication Information Lubrication Fitting LocationDescription Frequency Gauge Wheel Assemblies GearboxBlade Spindle Lubrication Driveline LubricationBlade Removal Blade InstallationBlade Servicing Blade SharpeningBelt Adjustment Procedure Figure Proper Torque for Fasteners StorageBlade Spindle Instructions Figure SERVIS-RHINO Page To the OWNER/OPERATOR/DEALER FM84-OMWPL-08/01 00775250C Printed U.S.A RHINO-SERVIS SERVIS-RHINOWARRANTY Registration Information Page Dealer Copy Page Customer Copy

FM84 specifications

The Servis-Rhino FM84 is a robust and versatile mower designed for efficient grass and brush management in various agricultural and landscaping applications. Renowned for its durability and performance, the FM84 is a product that exemplifies quality in the world of land maintenance equipment.

One of the key features of the FM84 is its sturdy construction. Built with a heavy-duty frame, the mower is designed to withstand the rigors of outdoor work. The 84-inch cutting width allows operators to cover large areas efficiently, making it ideal for both commercial and residential use. The mower's blade system consists of high-quality, sharp blades that ensure a clean cut, promoting healthy grass growth and a well-maintained appearance in managed landscapes.

The FM84 incorporates advanced technologies that enhance its functionality. It features a flexible cutting deck that adjusts to the terrain, allowing for effective mowing over uneven ground. This adaptability minimizes scalping and ensures an even cut, irrespective of the landscape's contours. Additionally, the mower comes equipped with a powerful hydraulic system, providing the necessary force to operate the cutting blades effortlessly. This hydraulic efficiency contributes to reduced wear on the machine and prolongs its lifespan.

Another standout characteristic of the Servis-Rhino FM84 is its user-friendly design. The mower is easy to operate, with intuitive controls that enable both seasoned operators and newcomers to handle the equipment seamlessly. The adjustable cutting height allows for customization based on the specific needs of the mowing task, whether that’s managing pastures, lawns, or overgrown fields.

Safety is a crucial factor in agricultural equipment, and the FM84 does not disappoint. It includes safety features such as a robust shield around the blades and an emergency shutoff mechanism, ensuring operator safety during use.

Moreover, the FM84 is compatible with a variety of tractors and utility vehicles, making it a versatile addition to any fleet. Its efficiency, durability, and ease of use make the Servis-Rhino FM84 a top choice for anyone in need of a reliable mower capable of handling diverse mowing challenges. Whether for commercial landscaping or maintaining large properties, the FM84 promises exceptional performance and lasting value.