Servis-Rhino FM84 manual Cutting Speed, Cutting Tips, Rear Discharge Models

Page 78

OPERATION

OPERATION

Enter the area to cut with the cutter operating at PTO speed and, if it becomes necessary to temporarily regulate engine speed during operations, increase or decrease the throttle gradually.

To transport, disengage the PTO, raise full transport height.

CUTTING SPEED

Proper ground speed for cutting will depend upon the height, type, and density of material to be cut.

Normally, ground speed will range from 1-1/2 to 3 mph. Tall dense material should be cut at low speed while thin medium height material can be cut at a faster ground speed.

CUTTING TIPS

Always operate PTO at recommended RPM when cutting. This is necessary to maintain proper blade speed and to produce a clean cut.

Under certain conditions, tractor tires may roll some grasses down and prevent them from being cut at the same height as the surrounding area. When this occurs, reduce the tractor ground speed, but maintain PTO RPM. The lower speed will permit grasses to be at least partially rebound and be cut. Taking a partial cut and/or reversing the direction of travel may also produce a cleaner cut.

As often as possible, stop mowing when other people are passing by. Although the Mower is shielded to prevent objects from being thrown out by the blades, no one shield device is 100% effective. The operator has greater knowledge of the dangers of being around this Mower while it is operational than the person on the street.

WARNING! Avoid personal injury. Pick up all rocks and other debris before cutting. Enter new areas

carefully. Cut material higher the first time to allow cutter to clear unseen objects. Never

assume an area is clear. Always check.

Extremely tall grass should be cut twice. Raise cutter and cut twice the desired height. Cut the second time at desired height at 90 degrees to first pass.

Remember, sharp blades produce cleaner cuts and use less power.

 

Before cutting, analyze the area to determine the best cutting proce-

FIGURE 1A

dure. Consider the height and type of material and the terrain type:

 

hilly, level or rough.

 

Grass is best cut when it is dry. Mowing wet grass can cause plugging

 

resulting in grass clumps behind the mower.

 

Grass should be mowed frequently as shorter clippings deteriorate

 

faster.

 

REAR DISCHARGE MODELS

 

The grass is discharged to the rear and slightly to the right. To keep

 

clippings off to streets and sidewalks mow two to three passes clockwise

 

as shown in Figure 1A.

 

FM84 08/01

Operation Section 4-4

© 2004 Alamo Group Inc.

 

Page 77 Page 79
Image 78
Page 77 Page 79
Contents FM84 To the OWNER/OPERATOR/DEALER Safety Training Makes the Difference Page Table of Contents Page Safety Section Peligro ¡LEA ELInstructivo Safety Skin, have the injury treated immediately by a physician Following rules SG-23 Safety Stop Mowing if Passersby are Within 100 Yards Unless Wait a minute...Save a life Parts Information See Your SERVIS-RHINO DealerSafety Decal Location QTY Level DescriptionSafety Decals FM84 FM84 08/01 Safety Section Alamo Group Inc Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Assembly Section Exceed Horsepower Recommendations Dealer SET-UP Instructions Frame AttachmentST Extended Position 2ND Extended Position CasterwheelattachmentsDriveline Attachment To Gearbox Operation Section Tractor Preparation Attaching Mower to Tractor Lift TypeCutting Height Adjustment Driveline Attachment to TractorStarting & Stopping Cutter Cutting Speed Cutting TipsRear Discharge Models Driveline Length Check Procedure Detaching and StoringBefore Operating or Transporting this Mower Driveline Length Front Gauge Wheel Interference CheckProblem Possible Cause Remedy StreakingDamaged Belt Maintenance Section Lubrication Information Lubrication Fitting LocationDescription Frequency Gearbox Gauge Wheel AssembliesDriveline Lubrication Blade Spindle LubricationBlade Sharpening Blade InstallationBlade Servicing Blade RemovalBelt Adjustment Procedure Figure Storage Proper Torque for FastenersBlade Spindle Instructions Figure SERVIS-RHINO Page To the OWNER/OPERATOR/DEALER FM84-OMWPL-08/01 00775250C Printed U.S.A RHINO-SERVIS SERVIS-RHINOWARRANTY Registration Information Page Dealer Copy Page Customer Copy

FM84 specifications

The Servis-Rhino FM84 is a robust and versatile mower designed for efficient grass and brush management in various agricultural and landscaping applications. Renowned for its durability and performance, the FM84 is a product that exemplifies quality in the world of land maintenance equipment.

One of the key features of the FM84 is its sturdy construction. Built with a heavy-duty frame, the mower is designed to withstand the rigors of outdoor work. The 84-inch cutting width allows operators to cover large areas efficiently, making it ideal for both commercial and residential use. The mower's blade system consists of high-quality, sharp blades that ensure a clean cut, promoting healthy grass growth and a well-maintained appearance in managed landscapes.

The FM84 incorporates advanced technologies that enhance its functionality. It features a flexible cutting deck that adjusts to the terrain, allowing for effective mowing over uneven ground. This adaptability minimizes scalping and ensures an even cut, irrespective of the landscape's contours. Additionally, the mower comes equipped with a powerful hydraulic system, providing the necessary force to operate the cutting blades effortlessly. This hydraulic efficiency contributes to reduced wear on the machine and prolongs its lifespan.

Another standout characteristic of the Servis-Rhino FM84 is its user-friendly design. The mower is easy to operate, with intuitive controls that enable both seasoned operators and newcomers to handle the equipment seamlessly. The adjustable cutting height allows for customization based on the specific needs of the mowing task, whether that’s managing pastures, lawns, or overgrown fields.

Safety is a crucial factor in agricultural equipment, and the FM84 does not disappoint. It includes safety features such as a robust shield around the blades and an emergency shutoff mechanism, ensuring operator safety during use.

Moreover, the FM84 is compatible with a variety of tractors and utility vehicles, making it a versatile addition to any fleet. Its efficiency, durability, and ease of use make the Servis-Rhino FM84 a top choice for anyone in need of a reliable mower capable of handling diverse mowing challenges. Whether for commercial landscaping or maintaining large properties, the FM84 promises exceptional performance and lasting value.
Top Page Image Contents