How to Connect

Figure 1

Figure 3

Figure 2

Figure 6

Figure 4

Figure 5

Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MC2301 Tube Power Amplifier until after the Loud- speaker Connections have been made. Failure to observe this could result in Electric Shock. For additional instruction on making Loud- speaker Connections contact your McIntosh Dealer or McIntosh Technical Support.

1.For Remote Power Control, connect a power control cable from the Control Center or Preamplifier Power Control Out to the MC2301 POWER CONTROL IN.

2.Connect a cable from the Balanced Output of a Mc- Intosh Preamplifier or Control Center to the MC2301 BALANCED INPUT. Place the INPUT MODE Switch

in the BALANCED Position.

Note: An optional hookup is to use an unbalanced cable and place the INPUT MODE Switch in the UNBAL- ANCED Position.

When connecting Loudspeakers to the MC2301 it is very important to use cables of adequate size, so there is little to no power loss in the cables. The size is specified in Gauge Numbers or AWG (American Wire Gauge). The smaller the Gauge number, the larger the wire size:

Loudspeaker Cable Distance vs Wire Gauge Guide

Loudspeaker	25 feet	50 feet	100 feet
Loudspeaker	(7.62 meters)	(15.24 meters)	(30.48 meters)
Impedance	(7.62 meters)	(15.24 meters)	(30.48 meters)
Impedance	or less	or less	or less
	or less	or less	or less
2 Ohms	12AWG	10AWG	8AWG
4 Ohms	14AWG	12AWG	10AWG
8 Ohms	16AWG	14AWG	12AWG

3.This McIntosh MC2301 Tube Power Amplifier is de- signed for the connection of a single Loudspeaker with an impedance of 2 ohms, 4 ohms or 8 ohms.

Note: The remaining Loudspeaker Terminals on the Amplifier should not be connected to another Loudspeaker.

4.Prepare the Loudspeaker Hookup Cables that attach to the Amplifier by choosing one of the methods below:

Bare wire cable ends:

Carefully remove sufficient insulation from the cable ends, refer to figures 1, 2 & 3. If the cable is stranded, care-

fully twist the strands together as tightly as pos-

sible.

Note: If desired,

the twisted ends can be tinned with solder to keep the strands together, or attach spade lug and/or banana connector.

Spade lug or prepared wire connection:

Insert the spade lug connector or prepared section of the cable end into the terminal side access hole, and tighten the terminal cap until the cable is firmly clamped into the

terminal so the

wires cannot slip out. Refer to fig-

ures 4, 5 & 6.

Banana plug connection:

Insert the banana plug into the hole at the top of the terminal. Refer to figures A and B.

Note: Banana Plugs are for use in the United States and Canada only.

When making Loudspeaker Connections to the MC2301 refer to the Connection Diagram on the next page. This is an example of a typical audio system, your system may vary from this, however the actual Loudspeaker would be connected in a similar manner.

5.Connect the Loudspeaker hookup cables from a single Loudspeaker to the output terminals that match the im- pedance of the Loudspeaker, being careful to observe the correct polarities. Output impedance connections of 2 ohms, 4 ohms and 8 ohms are provided. If the Loudspeaker’s impedance is in-between the available connections, use the nearest lower impedance connec- tion.

WARNING: Loudspeaker terminals are hazardous live and present a risk of electric shock.

6.Connect the MC2301 Power Cord to a live AC outlet.

MC2301 specifications

The McIntosh MC2301 is an exceptional tube amplifier renowned for its unique blend of classic design and modern technology. Launched by the prestigious audio brand McIntosh, this amplifier embodies the company’s commitment to high-quality sound reproduction. The MC2301 is specifically designed to deliver an unmatched listening experience for audiophiles and music enthusiasts alike.

At the heart of the MC2301 are its powerful tubes, producing 300 watts of output power. It employs a push-pull design using eight matched output vacuum tubes in a stunning monoblock configuration. This setup effectively delivers a rich, warm sound that only tube amplifiers can provide, contributing to a lush audio experience and bringing out nuances in music that solid-state amplifiers often miss.

One of the standout features of the MC2301 is its ability to preserve fidelity at various volume levels, thanks to its advanced circuit design. The amplifier incorporates McIntosh's patented Power Guard technology, which prevents clipping and distortion, ensuring that your music plays clearly and without compromise even at high volumes. This is particularly useful in high-demand listening sessions, where performance consistency is crucial.

The MC2301 also features the innovative Sentry Monitor circuit, which protects the amplifier from short circuits and overloads. This circuit continuously monitors the output stage and disconnects the output if it detects any issues, allowing the amplifier to maintain longevity and reliability in performance.

In terms of aesthetics, the MC2301 is visually stunning, maintaining McIntosh’s heritage style with its iconic glass front panel, illuminated logo, and distinctive blue watt meters. The build quality is remarkable, using carefully selected materials to ensure both durability and elegance.

Furthermore, the MC2301 includes balanced and unbalanced inputs, allowing for flexibility in connectivity. Its ability to pair seamlessly with various audio sources makes it a versatile choice for any high-fidelity system.

Overall, the McIntosh MC2301 amplifier is a perfect fusion of vintage-inspired sound craftsmanship and modern engineering, making it an outstanding choice for those seeking to elevate their audio experience. Its combination of power, protection, and pristine sound quality solidifies its status as a flagship product in the world of high-end audio. Whether powering a sophisticated home audio system or used in a professional setting, the MC2301 is sure to impress even the most discerning audiophiles.