Operator Safety

TBC-250/250PF/PFD,TBC-2501,TBC-2510,TBC-270PF/PN

TBC-270PN/PND,TBC-300/SDH/3010,TBC-340/D.TBC-340PF/D

Owner’s Manual

2. Warnings and safety instructions.

•Always wear a safety face shield or goggles.

•Always wear heavy, long pants, boots and gloves. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair so it is above shoulder length.

•Do not operate that tool when you are tired, ill or under the influence of alcohol, drugs or medication.

•Never let a child or inexperienced person operate the machine.

•Wear hearing protection.

•Never start or run the engine inside a closed room or building. Breathing exhaust fumes can kill.

•Keep handles free of oil and fuel.

•Keep hands away from cutting equipment.

•Do not grab or hold the unit by the cutting equipment.

•When the unit is turned off, make sure the engine has stopped before the unit is set down.

•When operation is prolonged, take a break from time to time so that you may avoid possible white finger disease, which is caused by vibration.

Tool Safety

•Inspect the entire tool before each use. Replace damaged parts. Check for fuel leaks and make sure all fasteners are in place and securely fastened.

•Replace parts that are cracked, chipped or damaged in any way before using the tool.

•Make sure the safety guard is properly attached.

•Keep others away when making carburetor adjustments.

•Use only accessories as recommended for this tools by the manufacturer.

WARNING!

Never modify the tool in any way. Do not use the tool for any job except that for which it is intended.

Fuel Safety

NOTE!

•Empty the fuel tank before storing the tool. Especially, in the case of over three month storage, it is a must otherwise fuel may corrode causing carburetor damage. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak.

•Mix and pour fuel outdoors and where there are no sparks or flames.

•Use a container approved for fuel.

•Do not smoke or allow smoking near fuel or the tool or while using the tool.

•Wipe up all fuel spills before starting engine.

•Move at least 3 m (10 ft) away from fueling site before starting engine.

•Stop engine before removing fuel cap.

•Store tool and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

WARNING!

Anti-vibration systems do not guarantee that you will not sustain white finger disease or carpal tunnel syndrome. Therefore, continual and regular users should monitor closely the condition of their hands and fingers. If any of the above symptoms appear, seek medical advice immediately.

Cutting Safety

•Do not cut any material other than grass and brush.

•Inspect the area to be cut before each use. Remove objects which can be thrown or become entangled.

•For respiratory protection, wear an aerosol protection mask when cutting the grass after insecticide is scattered.

•Keep others including children, animals, bystanders and helpers outside the 15 m (50ft) hazard zone. Stop the engine immediately if you are approached.

•Always keep the engine on the right side of your body.

•Hold the tool firmly with both hands.

•Keep firm footing and balance. Do not over-reach.

•Keep all parts of your body away from the muffler and cutting attachment when the engine is running.

•Keep the cutting attachment below waist level.

Maintenance Safety

•Maintain the tool according to recommended procedures.

•Disconnect the spark plug before performing maintenance except for carburetor adjustments.

•Keep others away when making carburetor adjustments.

•Use only genuine replacement parts as recommended by the manufacturer.

Transport and storage

•Carry the tool by hand with the engine stopped and the muffler away from your body.

•Allow the engine to cool, empty the fuel tank, and secure the tool before storing or transporting in a vehicle.

•Empty the fuel tank before storing the tool. It is recommended that the fuel be emptied after each use. If fuel is left in the tank, store so fuel will not leak.

•Store tool out of the reach of children.

•Clean the unit carefully and store it in a dry place.

•Make sure engine switch is off when transporting or storing.

•When transporting in a vehicle, cover blade with blade cover.

If situations occur which are not covered in this manual, take care and use good judgment. Contact your dealer if you need assistance.

Pay special attention to statements preceded by the following words:

WARNING!

Indicates a strong possibility of severe personal injury or loss of life, if instructions are not followed.

CAUTION!

Indicates a possibility of personal injury or equipment damage, if instructions are not followed.

NOTE!

Helpful information for correct function and use.

www.tanaka-usa.com

custsvc@tanaka-ism.com

TBS270PF/PN, TBC-300/SDH3010, TBC-2501, TBC-250, TBC-340PF/PFD specifications

Tanaka’s innovative range of welders, including the TBC-250PF/PFD, TBC-2510, TBC-270PFD/PND, TBC-2501, and TBC-300/SDH/3010, has positioned the brand as a leader in providing high-quality welding solutions. These machines are widely recognized for their durable construction, advanced technology, and user-friendly features, making them ideal for both industrial and commercial applications.

The TBC-250PF/PFD series is equipped with a powerful inverter system that ensures high-efficiency performance and consistent arc. Its Pulse function allows for precise welding, which is particularly useful for thin materials or delicate projects. This model also incorporates soft start technology, reducing the initial current surge, protecting both the machine and the workpiece from damage.

Moving on to the TBC-2510, this model stands out for its versatility and capacity to handle a variety of welding processes, including TIG and MIG. It features a digital display for easy monitoring and adjustments, along with an automatic temperature control system that prevents overheating. The TBC-2510's compact design also makes it highly portable, suited for both shop and fieldwork.

The TBC-270PFD/PND further enhances the lineup with its dual-functionality for MIG and flux-cored welding. This machine includes advanced synergic control technology, allowing users to set wire diameter and gas type, automatically adjusting the parameters for optimal welding results. The inclusion of a built-in cooling system helps prolong the machine's lifespan by preventing overheating during extended use.

In the TBC-2501, Tanaka introduces a model that combines robust performance with ease of use. Designed for both beginners and experienced welders, it features adjustable welding current and a simple interface, making it accessible to a wide range of users. Its lightweight construction enhances portability, allowing for easy transport to job sites.

Lastly, the TBC-300/SDH/3010 showcases the brand's commitment to innovation with its state-of-the-art welding technology. It offers a combination of high welding speed and quality, making it perfect for high-demand applications. This unit also incorporates advanced safety features, ensuring operator protection during use.

In conclusion, the Tanaka TBC welding machines represent a perfect blend of advanced technology, user-friendly designs, and durable construction, catering to the diverse needs of the welding industry. Their features make them suitable for both novice and seasoned welders, becoming an invaluable tool in any workshop or construction site.