|
|
|
|
|
|
| Installation |
Installation |
|
|
|
|
|
|
|
The MC207 can be placed upright on a table or shelf, | (3.81cm) below the bottom and 1 inch (2.54cm) on each | ||||||
standing on its four feet. It also can be custom installed in a | side of the amplifier, so that airflow is not obstructed. Al- | ||||||
piece of furniture or cabinet of your choice. The four feet | low 20 inches (50.8cm) depth behind the front panel. Al- | ||||||
may be removed from the bottom of the MC207 when it is | low 1 inch (2.54cm) in front of the mounting panel for | ||||||
custom installed as outlined below. The four feet together | knob clearance. Be sure to cut out a ventilation hole in the | ||||||
with the mounting screws should be retained for possible | mounting shelf according to the dimensions in the drawing. | ||||||
future use if the MC207 is removed from the custom instal- |
|
|
|
|
| ||
lation and used free standing. It also can be custom in- |
|
|
|
|
| ||
stalled in a piece of |
|
|
|
|
|
|
|
furniture or cabinet |
|
|
|
|
|
| |
of your choice The |
|
|
| 43.34cm |
|
|
|
required panel cut- |
|
|
|
|
|
|
|
out, ventilation cut- |
|
|
|
|
|
|
|
out and unit dimen- |
|
|
|
|
|
|
|
sions are shown. |
|
|
|
|
|
|
|
Always provide |
|
|
|
|
|
|
|
adequate ventilation | MC207 Front Panel |
|
|
|
|
| |
for your MC207. | Custom Cabinet Cutout |
|
|
|
|
| 21.11cm |
Cool operation en- |
|
|
|
|
|
|
|
sures the longest |
|
|
|
|
|
|
|
possible operating |
|
|
|
|
|
|
|
life for any elec- |
|
|
|
|
|
|
|
tronic instrument. |
|
|
| 6" |
|
|
|
Do not install the |
|
|
| 15.24cm |
| Cutout Opening |
|
MC207 directly |
| Cabinet |
|
|
| ||
above a heat gener- |
| Front |
|
| for |
| |
|
|
| Custom Mounting |
| |||
ating component |
| Panel |
|
|
| ||
|
|
|
|
| |||
such as a high pow- |
| Opening |
|
|
|
|
|
ered amplifier. If all |
| for Ventilation |
|
|
|
| |
the components are |
|
|
|
|
|
|
|
installed in a single |
|
|
|
|
|
|
|
cabinet, a quiet run- | MC207 Side View |
|
|
|
|
|
|
ning ventilation fan |
|
|
|
|
|
| |
in Custom Cabinet |
|
|
|
|
|
| |
can be a definite as- |
|
|
|
|
|
| |
|
|
|
|
|
|
| |
set in maintaining |
|
|
|
|
|
|
|
all the system com- |
|
|
| Cutout Opening for Ventilation |
| ||
ponents at the |
| Support | Chassis | ||||
|
|
| |||||
coolest possible op- |
| Shelf |
|
|
| Spacers | |
erating temperature. |
|
|
| 8.57cm |
|
|
|
|
|
|
|
|
|
| |
A custom cabinet |
|
|
|
|
|
| |
installation should |
|
|
|
|
|
| |
provide the follow- |
|
|
| 31.12cm | 11" |
| |
ing minimum spac- | MC207 Bottom View |
|
| Cutout |
| ||
ing dimensions for | in Custom Cabinet |
|
| Opening |
| 27.9cm | |
Center the |
| for | 31.43cm | ||||
cool operation. Al- |
|
| |||||
| opening horizontally | Ventilation |
| ||||
low at least 6 inches |
| 40.00cm |
| ||||
| with the |
|
|
| |||
|
|
|
|
| |||
(15.24cm) above the |
| MC207 Chassis |
|
|
| ||
top, 2 inches |
|
|
| 25.08cm |
|
| |
|
|
|
|
|
| ||
|
|
|
| 29.21cm |
|
| |
6 |
|
|
|
|
|
|
|