MTD 24A-020D000 Clean the equipment thoroughly, Wipe equipment with a oiled rag to prevent rust

Page 11

•Remove the shoulder screws and bell washers that go through the pivot arms and height bracket adjusters to the front support brace.

•Remove the three screws on the upper housing that secure the nozzle cover and the nine screws that secure the lower housing to the upper housing. See Figure 12.

Housing

 

Screw

 

Nozzle

Lower Housing

Screws

Screws

 

Figure 12

•Remove lock nut that secures flail screen to the lower housing. The flail screen does not have to be removed.

•Remove the hex bolt, lock washer, and flat washer that secure the impeller assembly to the crankshaft. See Figure 13.

•Apply lubricant to the threads of impeller removal tool and then thread the tool into the crankshaft. Stop when the impeller assembly can move on the crankshaft.

•Remove the impeller assembly from the crankshaft. Unthread the impeller removal tool from the impeller assembly.

•Remove the blade using a 3/16” allen wrench on the outside of the blade and 1/2” wrench on the impeller assembly.

•Replace or sharpen chipper blade.

•When sharpening blade, protect hands by using gloves and follow the original angle of grind.

•Reassemble by performing the previous steps in reverse order.

•Tighten blade screws to 210-250 in-lbs. Tighten impeller bolt to 375-425 in-lbs.

NOTE: Make certain chipper blade is reassembled with the sharp edge facing upward. See Figure 14.

Flail

Chipper

Blade

Blade

 

 

Impeller

 

Assembly

Figure 14

Upper

Storing Your Chipper Shredder Vacuum

• Clean the equipment thoroughly.

Housing

• Wipe equipment with a oiled rag to prevent rust.

Chipper

Blade

• Refer to engine manual for correct engine storage

Impeller

Assembly

instructions

 

• Store unit in a clean, dry area. Do not store next to

 

corrosive materials such as fertilizer.

Hex Bolt

 

Lock Washer

 

Flat Washer

 

Flail

 

Blade

 

BOTTOM VIEW

 

Figure 13

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents OPERATOR’S Manual Calling Customer Support Table of ContentsFinding Model Number Preparation Important Safe Operation PracticesTraining Operation Maintenance and StorageLoose Parts In Carton See Figure Disconnecting Spark Plug WireAssembling Your Chipper Shredder Vacuum Removing Unit From CartonAttaching The Blower Chute If Equipped Attaching The HandleAttaching The Bag Stopping Engine Know Your Chipper Shredder VacuumOperating Your Chipper Shredder Vacuum Maintaining Your Chipper Shredder Vacuum Nozzle Height AdjustmentEngine MaintenanceLubrication Removing The Flail ScreenRefer to engine manual for correct engine storage Clean the equipment thoroughlyStore unit in a clean, dry area. Do not store next to Wipe equipment with a oiled rag to prevent rustProblem Cause Remedy TroubleshootingPage Model 24A-020D000 Part Description Model 24A-020D000 Model 24A-020D000 Contenido ÍndiceBúsqueda DEL Número DE Modelo Servicio Telefónico DE Asistencia AL ClienteCapacitación Sección 1 Medidas Importantes DE SeguridadMantenimiento Y Almacenamiento Colocación de la bolsa Extracción de la unidad de la cajaDesconexión del cable de la bujía Montaje de la manijaCanal de la cortadora Instalación del canal de sopladoSi está incluidoBolsa Manija de la bolsaEncendido del motor Detención del motorCarga de gas y aceite Descarga de la bolsa Mantenimiento Funcionamiento de la cortadora trituradora aspiradoraAjuste de la altura del pico LubricaciónResponsabilidades del cliente Afilado o recambio de las hojas de la cortadoraCaja Tornillo Pico Caja inferior Tornillos Almacenamiento de la cortadora trituradora aspiradoraProblema Causa Solución Sección 6 Guía Para LA Solución DE ProblemasPage Page Page DEL Fabricante Garantía Limitada MANUFACTURER’S Limited Warranty
Top Page Image Contents