MTD 690 through 699 manual Activating & Charging Battery, Attaching Steering Wheel, Attaching Seat

Page 8

•Compare the battery in your lawn tractor (located under the seat) with the illustration above. Type “A” batteries are activated and are ready to use. Type “B” batteries must be filled with battery fluid (acid) and charged before they are put into service. Follow instructions which apply to the battery in your lawn tractor only.

Activating & Charging Battery

(Type “B” Battery Only)

WARNING: Do not activate battery (i.e. fill with battery acid) until battery is actually placed in service. Read warnings about battery usage in the previous page before activating the battery.

•Pivot the seat pivot bracket forward. Unhook the strap which secures the battery (hook is on rear frame, under the fender). Disconnect the positive cable from the positive terminal. Save the hardware for reassembly.

•Remove the battery from the lawn tractor, paying attention to how the battery is placed in the unit, and how the drain tube (attached to the battery) is routed.

•Activate the battery as instructed in the “Quick Start” brochure included with the battery fluid. Read instructions carefully.

NOTE: You can continue to assemble the lawn tractor while the battery is standing for 30 minutes after acid fill-up, and later while you are charging the battery.

IMPORTANT: To obtain maximum life from the battery, charge it prior to initial use.

•Battery P/N 725-1705D: Charge at 2-3 amps for one hour.

•Battery P/N 725-1707D, 725-0453G, and 725- 1750: Charge at 6 amps for one hour.

•Charge battery after the 30-minute standing period.

NOTE: If you charge the battery at a lower AMP rate, use a hydrometer to make sure the battery is completely charged. The hydrometer should read 1.260

minimum at an electrolyte temperature of 60-110oF.

WARNING: Do not charge the tractor battery at more than 6 amps.

Attaching Steering Wheel

•The hardware for attaching the steering wheel has been packed inside the steering wheel. Carefully pry off the steering wheel cap and remove the hardware.

•Remove the steering bellow from the lift lever on the right side of the tractor.

•Place the steering bellow over the steering shaft extending through the dash. See Figure 2 .

NOTE: If the openings on each end of the steering bellow are of two sizes, the smaller end goes down against the dash of the lawn tractor.

•With the wheels pointing straight, place the steering wheel over the steering shaft, positioning the steering wheel as desired.

•Place the washer with the cupped side down over the steering shaft. Secure with hex lock bolt. See Figure 2 .

NOTE: If your tractor steering wheel cap is square, you must use a socket wrench.

•Place the steering wheel cap over the center of the steering wheel and press it with your hand.

Steering

Hex Lock

Wheel Cap

Bolt

Cupped

Washer

Steering

Bellow

Steering

Shaft

Figure 2

Attaching Seat

NOTE: Your tractor is equipped with one of the following types of seats. Identify the seat type from the illustrations below, and follow instructions pertaining to your tractor.

Manual Adjustment Seat

•Remove the four screws which secure the seat to the seat pivot bracket. See Figure 3 .Turn the seat around and place it in position against the seat pivot bracket, lining up the slotted holes in the pivot bracket with the holes in the seat. Select desired position for the seat, and secure with the four screws removed earlier.

Screws

Seat

Pivot

Bracket

Figure 3

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual Table of Contents Slope Operation Important Safe Operation PracticesGeneral Operation Do Not ServiceChildren Your Responsibility Slope Guage Handling Battery Identifying Battery TypeAssembling Your Lawn Tractor UnpackingActivating & Charging Battery Manual Adjustment SeatAttaching Steering Wheel Attaching SeatAttaching Chute Deflector Installing Mulching PlugQuick Adjustment Seat Installing Battery Type a BatteryType B Battery Tire PressureKnow Your Lawn Tractor Optional Features Operating Your Lawn Tractor Gas And Oil Fill-UpStarting Engine Stopping EngineSetting Cutting Height Manual Adjustment SeatQuick Adjustment Seat Grass CollectorBrake Adjustment Wheel AdjustmentDeck Leveling Cutting Deck EngagementBattery Care Cleaning BatteryMaintaining Your Lawn Tractor CarburetorLubrication Cutting BladesBelt Replacement Blade Mounting TorqueDeck Belt 38 and 42 Decks Deck Belts 46 DeckCleaning Engine & Deck Hydrostatic Transmission CoolingFuel Filter Drive BeltOil Drain Valve If equipped EngineOil Drain Sleeve If equipped Optional Equipment Description Model NoTrouble Shooting Guide Trouble Possible Causes Corrective ActionYour Notes MANUFACTURER’S Limited Warranty

690 through 699 specifications

MTD (Motor Technology Division) has developed a remarkable series of compact tractors under the model numbers 690 through 699, which have gained popularity among agricultural professionals and hobby farmers alike. These models are designed to provide powerful, efficient, and versatile performance for a variety of farming tasks.

One of the standout features of the MTD 690 to 699 series is their ergonomic design, which emphasizes operator comfort and ease of use. The tractors are equipped with adjustable seats, intuitive controls, and clear visibility from the operator’s station, ensuring that users can work for extended periods without fatigue. This focus on comfort makes these tractors suitable for both full-time farmers and those who engage in part-time farming or landscaping.

In terms of technology, this series is fitted with advanced engine options that deliver impressive horsepower. The engines are designed for optimal fuel efficiency, reducing operational costs and environmental impact. Additionally, features like electronic fuel injection enhance performance, ensuring reliable startup and smooth operation under varying load conditions.

The transmission systems found in the MTD 690 to 699 models are engineered for versatility. Many models are equipped with hydrostatic transmissions, allowing for seamless speed and directional changes without the need for clutch engagement. This capability is particularly useful when maneuvering in tight spaces or performing tasks that require precision.

Another defining characteristic of this series is their hydraulic systems, which provide powerful lifting capabilities. This makes it easier to attach and operate a wide range of implements and attachments, from loaders to mowers, enhancing productivity on the farm. The hydraulic systems are designed with user-friendliness in mind, allowing for quick attachment changes that reduce downtime during chores.

Durability is also a hallmark of MTD's 690 through 699 tractors. Constructed with robust materials and designed to withstand harsh working conditions, they feature reinforced frames and components that provide longevity and reliability. This durability ensures that the tractors can handle demanding tasks day in and day out, making them a dependable asset for any agricultural operation.

In summary, the MTD 690 through 699 series offers a blend of comfort, efficiency, and technology, making them an attractive option for anyone looking to enhance their farming capabilities. With powerful engines, user-friendly controls, advanced hydraulic systems, and exceptional durability, these compact tractors are poised to meet the needs of today’s diverse agricultural landscape.
Top Page Image Contents