MTD Series 400 warranty Setup Adjustments

Page 6

3

Setup and

Adjustments

WARNING

Disconnect and ground the spark plug wire as instruct- ed in the separate engine manual.

Your mower is shipped with the handle in the higher height position. NOTE: Each end of the lower handle must be placed in the same relative position.

IMPORTANT This unit is shipped

WITHOUT GASOLINE or OIL. After assem- bly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit.

Figure 1

Figure 2

�

Figure 3

1.Remove loose parts and any packing material which may be between upper and lower handles.

a.Pull up and back on the upper handle to raise the handle from position A into the operating position B. See Figure 1.

b.Tighten hand knobs (star knobs) securing upper handle to lower handle. Make sure that each carriage bolt is seated properly in the handle.

NOTE: On some models wing nuts have been replaced with star knobs. Figures show wing nuts only.

2.Locate hairpin clip in one hole on the weld pin on each side of lower handle.

a.Remove hairpin clip from this hole. Using a pair of pliers, insert hairpin clip into the other hole on the weld pin. Repeat on other side.

b.Place one carriage bolt (found in the hardware pack included with your unit) in the upper hole of the right handle mounting bracket from the inside outward. See Figure 2. Secure with one wing nut (star knobs). Repeat process on the left side.

3.Rope guide Setup as follows, see Figure 3:

a.Hold the blade control against the upper handle. Position A.

b.Slowly pull starter rope out of engine. Position B.

c.Slip starter rope into the rope guide. Position C.

d.Tighten rope guide wing nut (star knobs).Position D.

4.Insert post on cable ties into holes provided on the lower handle. Pull cable tie tight and trim excess. See Figure 4.

5.Each wheel has a height adjustment lever to change the cutting height of the mower. To change the height of cut, squeeze adjuster lever toward the wheel, moving up or down to selected height. See Figure 5.

Figure 4

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OPERATOR’S Manual Rotary Mower Model SeriesTable of Contents Finding and Recording Model NumberCustomer Support Slope Gauge General Operation SafeYour Responsibility Slope OperationSafe Operation Practices ServiceGeneral Service ChildrenSetup Adjustments To assemble the grasscatcher To remove grass catcher and utilize the mulching featureSide discharge is an optional feature Attaching Grass Catcher to MowerOperating Your Lawn Mower Know Your Lawn MowerOperating Your Lawn MowerMaintenance Remove blade and adapter from the crankshaft Rear Flap ReplacementOff-Season Storage Tighten the hex bolt to the torque listed belowTrouble Shooting Problem Cause RemedyWarranty TWO Year Limited Warranty

Series 400 specifications

The MTD Series 400 is a cutting-edge line of equipment designed specifically for efficiency and versatility in outdoor maintenance. With design enhancements tailored for both residential and commercial users, the Series 400 stands out in its category thanks to its robust construction, user-friendly controls, and advanced technology.

One of the main features of the MTD Series 400 is its powerful engine. Equipped with an efficient four-stroke engine, it delivers exceptional performance while maintaining low emissions, making it environmentally friendly. This engine also ensures reliable operation across various terrains, from flat lawns to hilly regions, providing users with the confidence to tackle any outdoor task.

Another notable characteristic is the ergonomic design. The Series 400 incorporates adjustable handlebars and cushioned grips that promote comfort for extended use. This design consideration reduces fatigue and enhances user control, making it suitable for both novice and experienced users alike.

The Series 400 incorporates several advanced technologies that set it apart from competitors. For instance, its intuitive control panel simplifies operation, allowing users to easily switch between different settings without confusion. Moreover, the inclusion of a quick-start feature means users can get to work without unnecessary delays, enhancing overall productivity.

Durability is a hallmark of the MTD Series 400, with high-quality materials used throughout its construction. Reinforced components and weather-resistant finishes ensure that the equipment can withstand the rigors of outdoor use, thus extending its lifespan significantly.

One of the standout technologies in the Series 400 is its cutting system, which is optimized for precision and performance. This system allows for adjustable height settings, enabling users to achieve the desired grass length while promoting healthy lawn growth. This adaptability is crucial for meeting diverse gardening needs.

Additionally, the MTD Series 400 is designed with maintenance in mind. Its accessible components make routine checks and servicing straightforward, which is critical for ensuring long-term functionality and reliability.

In summary, the MTD Series 400 combines powerful performance, ergonomic design, advanced technology, and durability to meet the needs of outdoor maintenance. Whether for residential gardens or commercial landscapes, the Series 400 equips users with the tools needed to achieve optimal results efficiently and effectively.
Top Page Image Contents