Multiquip gbe/gbce manual Extension Pole Gbce Only Extends mast height by 40 inches

Page 15

components

Figure 3 shows the location of the controls and components for the GBC/GBCE Lighting System.The functions of each control is described below:

1.Balloon Cover — Stores balloon when GBC/GBCE is not in use. Allow a sufficient amount of time for the lamp to cool down before storing balloon. Possibility exists of balloon getting burned.

2.Balloon — Made of heat resistant polyester, with a diameter of 47.2 inches (1,200 mm). Balloon is self- inflating and inflates in less than 20 seconds.

3.Velcro — Used to easily attach optional message strip to the balloon.

4.Buckle — Used to hold the balloon together when storing inside the cover.

5.AC Power Cable — connects to the AC power source (generator) on one end and to the lamp connector on the other end with quick-disconnect connector.

6.Cart — holds the generator and can be steered easily to transport GBC/GBCE to different locations.

7.Locking Clamps — To secure the generator to the cart platform, place clamps around the pipe frame of the generator. Tighten securely to prevent movement.

8.Tire — The GBC/GBCE uses four pneumatic tires for easy maneuverability.

9.Brake Pad — When the brake pedal is pressed, this pad will strike and hold the rear tires in place.

10.Strap Slots — Allows suitcase generators to be strapped to cart securely.

11.Outriggers — provides stability to the GBC/GBCE. When raising the mast, outriggers should always be deployed.

12.Counter Weight — Locks the outriggers in place when they are deployed or stowed.

13.Brake Pedal — Step on this pedal and pull back T-handle to apply the brakes. To release the brakes, press down and hold brake pedal again then release.

14.T-Handle— Moves the GBC/GBCE in either forward or reverse direction by pulling back or pushing forward. The T-handle also allows the cart to be steered left or right.

15.Mast — This mast is comprised of three separate stages. The mast can be raised in excess of 8 feet (without balloon).

WARNING

When raising the mast, always be on the lookout for overhead obstructions.

16.Mast Bolt — Loosen to raise mast and tighten to keep the mast in place when raised to the desired height.

17.AC Power Cable Connector — Connect this quick- disconnect plug to the balloon connector.

18.Message Strip (OPTIONAL) — a 12 x 43 inch message strip (Part No. GBBALD1) may be attached to the balloon. The message strip can be purchased separately.

19.Zipper — Zips up balloon to completely close it when lamp is in place.

20.Lamp Holder — Holds lamp in place. Lamp is screwed into socket.

21.Balloon Connector — Connect this connector to the AC power cable connector.

22.Lamp/Balloon Bolt — used to tighten mast when attached to the lamp/balloon assembly.

23.Fan Motor (Blower) — inflates the balloon as soon as power is applied to the GBC/GBCE.

24.Lamp — 1000 watt metal halide bulb with pure white light for maximum illumination.

25.Lamp Guard — Protects the lamp from being hit by objects and balloon material from touching lamp.

26.Extension Pole (GBCE Only) — Extends mast height by 40 inches.

gbc/GBCE lighting system • operation and parts manual — rev. #1 (03/25/14) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents This Manual Must Accompany the Equipment AT ALL Times Model GBC/GBCEProposition 65 warning GBC/GBCE Table of ContentsChoose from three easy options Safety Information SaFety messagesSaFety symBols General saFety  never unplug the lamp’s AC power cable during operation Lighting system saFetyLamp saFety  never attempt service on a running machinePower Cord/Cable safety Balloon saFetyGenerator saFety EleCtriCal saFetyCart Type No Lifiting Hook Transporting SafetyLoading and Unloading Cart Type With Lifiting HookSpecifications 305 Dimensions40.5 029 28.3 718.8Illumination Range Footcandle plotExtension Cord Gauge Selection General informationComponents Gbce onlyExtension Pole Gbce Only Extends mast height by 40 inches Fold the balloon cover into itself and zip it up. See Figure SetupConnecting the Power Cable Deploying outrigger OperationApplying Parking Brake Releasing Parking BrakeRaising the mast Stowing OutriggerShutting down lamp only Applying PowerLowering the Mast ShutdownStorage Disconnect the lamp connector from the AC power cableMaintenance Replacing LampRemove the lamp guard Replacing Balloon Unzip the top and bottom of the balloon. See FigureZip up the top and bottom of the new balloon. See Figure Locking Air Plate Filter replacementWait for lamp to cool down Loose?Lamp does not light Unplug all other appliancesC11 C10 C5 C8 Power cable Defective or worn cable? Replace Plug Lamp Base Lamp base loose? Screw in securely ConnectorAdjust Link for front shaft Spray grease Brake Not working properly? AdjustBlack Electronic White Ballast Wiring diagramPage Explanation of Code in Remarks Column GBC/GBCE lIGHTING System 1 to 3 units Suggested Spare PartsNameplates and decals GloBugTM Lighting SystemA400193500 A400193800A400193400 A400193700Balloon and lamp assy A300160601 0024304008 Screw M4x8 A300167500E000038200 0025304025 Screw & Washer M4x25 A300174000Mast assy A400187600 A300169400A300169300 A300169200Base assy A300056800 A100054500A300147201 A300147301Outrigger assy A400176901 A3001622021641001430 A400175302Terms and Conditions of Sale Parts Page HERE’S HOW to GET Help

gbe/gbce specifications

Multiquip’s GBE/GBCE series represents a fusion of innovation and reliability in the construction equipment market. These generators are specifically designed to meet the diverse needs of contractors and service providers, offering both performance and versatility in a compact package.

One of the main features of the GBE/GBCE generators is their robust construction. Designed to withstand harsh job site conditions, these units are housed in durable enclosures that provide excellent protection against environmental elements. The weather-resistant design ensures that the generators can operate efficiently in various climates, making them suitable for both indoor and outdoor applications.

Power delivery is another hallmark of the GBE/GBCE series. With a wide range of models available, these generators are capable of producing power outputs that cater to different project requirements. The GBE series focuses on efficiency and performance, while the GBCE series introduces advanced starting technology that enhances reliability, reducing the chances of downtime on critical workdays.

Equipped with advanced engine technology, these generators boast low emissions and noise levels, making them compliant with environmental regulations. The engines are designed for fuel efficiency, helping to minimize operational costs while maximizing uptime. Furthermore, the incorporation of innovative control systems allows for easy monitoring of performance metrics, providing operators with real-time information on generator status.

Safety is a prime consideration, and the GBE/GBCE series comes with numerous built-in safety features. These include automatic shutdown mechanisms that activate in the event of low oil levels or high temperatures, ensuring that the generator does not suffer damage during operation. The ergonomic design of the control panel enhances user experience, allowing for intuitive operation even for those with minimal experience in generator management.

In summary, Multiquip's GBE/GBCE generators embody features that prioritize durability, efficiency, and ease of use. The combination of advanced technology, environmental compliance, and user-friendly controls positions these generators as ideal solutions for a wide range of applications, from commercial construction projects to emergency backup power requirements. With a commitment to performance and reliability, the GBE/GBCE series continues to be a trusted choice for professionals in the field.
Top Page Image Contents