Multiquip GAC3.6HZ Outdoor Installation, Indoor Installation, Placement, Generator Grounding

Page 15

installation

Outdoor Installation

If possible install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around.

The installation site must be relatively free from moisture and dust. All electrical equipment should be protected from excessive moisture. Failure to do will result in deterioration of the insulation and will result in short circuits and grounding.

Foreign materials such as dust, sand, lint and abrasive materials have a tendency to cause excessive wear to engine and alternator parts.

Indoor Installation

WARNING

Pay close attention to ventilation when operating the generator inside tunnels and caves. The engine exhaust contains noxious elements. Engine exhaust must be routed to a ventilated area

Exhaust gases from gas engines are extremely poisonous. Whenever an engine is installed indoors the exhaust fumes must be vented to the outside. The engine should be installed at least two feet from any outside wall. Using an exhaust pipe which is too long or too small can cause excessive back pressure which will cause the engine to heat excessively and possibly burn the valves.

placement

The generators should always be placed on a flat level surface when it is running. DO NOT place the generators on slopes, the possibility exists that the generators could slide.

DANGER

An electric shock is apt to happen when vibrators are used. Pay close attention to handling when operating vibrators and always use rubber boots and gloves to insulate the body from a short circuit.

Generator Grounding

To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.

Article 250 (Grounding) of the National Electrical Code (NEC) provides guide lines for proper grounding and specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

NEC articles 250-64(b) and 250-66 set the following grounding requirements:

1.Use one of the following wire types to connect the generator to earth ground.

a.Copper - 10 AWG (5.3 mm2) or larger.

b.Aluminum - 8 AWG (8.4 mm2) or larger.

2.When grounding the generator (Figure 2) connect the ground cable between the lock washer and the nut on the generator and tighten the nut fully. Connect the other end of the ground cable to earth ground.

3.NEC article 250-52(c) specifies that the earth ground rod should be buried a minimum of 8 ft. into the ground.

NOTICE

When connecting the generator to any buildings electrical system ALWAYS consult with a licensed electrician.

gac3.6hz 60 hz GENERATOR • operation and parts manual — rev. #1 (03/31/10) — page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model gac3.6hz GAC3.6HZ Portable 60 Hz Generator Table of ContentsChoose from three easy options SaFeTY messages Safety InformationGeNeRaTOR saFeTY GeNeRal saFeTYFuel saFeTY ENgiNe saFeTYBaTTeRY saFeTY elecTRic sTaRT ONlY ElecTRical saFeTYPower cord/cable safety Grounding safetyENviRONmeNTal saFeTY TRaNspORTiNg saFeTYPage Specifications Generators Specifications gENERATOREffects of Altitude and Heat Specifications engine18.9 480 MM DimensionsPage Connecting the Ground InstallationGenerator Grounding Outdoor InstallationIndoor Installation PlacementGeneral information GeneratorControl Box Gfci Ground Gfci ground connection point Components generatorComponents generator General Inspection Prior to Operation Ground Power Tools Extension CableMain Circuit Breaker Before Starting Engine Oil CheckFuel Check Operation Before Starting the EngineStarting the Engine Place main circuit breaker in the on position Stopping the Engine Operation/shutdownGenerators Storage Preparation for long term storageFirst Every MaintenanceWeekly MaintenanceEngine Air Cleaner DailySW2 Generator wiring diagramEngine Troubleshooting TroubleshootingWeak in power Water in fuel system? Output LoadNo Load Load ActivePage Explanation of Code in Remarks Column Spark Plug Suggested Spare PartsCAP Fuel Tank Filter Fuel5561008 and below Nameplate and decalsPart Name Generator assy Surge Abssorber Rotor AssyField Coil RECTIFIER, D3SB80Control BOX assy Slow Down Unit Idle Control SwitchOperation Switch Control BOXPipe Frame assy Rubber Suspension Pipe FrameBracket BaseMuffler assy Muffler SealTapping Screw Honda gx240k1/u1edn2 engine cylinder head assy CLIP, Valve Guide Head COMP., CylnderGUIDE, IN. Valve Over Size GUIDE, EX. Valve Over SizeHonda gx240k1/u1edn2 engine cylinder barrel assy CORD, Earth Switch ASSY., OIL LevelBarrel ASSY., Cylinder SHAFT, Governor ARMHonda gx240k1/u1edn2 engine crankcase cvr. assy PACKING, Case Cover WEIGHT, GovernorHOLDER, Governor Weight PIN, Governor WeightHonda gx240k1/u1edn2 engine Crankshaft assy KEY SPECIAL, Woodruff Honda gx240k1/u1edn2 engine Piston assy Piston STD BOLT, Connecting RODRing SET, Piston STD Ring SET, PistonHonda gx240k1/u1edn2 engine cAMshaft assy ARM, Valve Rocker SPRING, Weight ReturnNUT, Pivot Adjusting ROD, PushHonda gx240k1/u1edn2 engine Recoil Starter assy SPRING, Starter Return PULLEY, Recoil StarterRATCHET, Starter SPRING, FrictionHonda gx240k1/u1edn2 engine FAN Cover assy GROMMET, Drain Hole CLIP, Wire HarnessCover COMP., FAN ShroudHonda gx240k1/u1edn2 engine caRBURETOR assy Float SET PACKING, AIR CleanerGasket SET Valve SET, FloatHonda gx240k1/u1edn2 engine caRBURETOR assy VALVE, Dashpot Check ROD, Choke ControlGROMMET, Choke ROD GUIDE, Choke RODHonda gx240k1/u1edn2 engine AIR Cleaner assy STAY, AIR Cleaner ELEMENT, AIR CleanerSEPARATOR, AIR Cleaner Case COMP., AIR CleanerHonda gx240k1/u1edn2 engine Flywheel assy NUT, SPECIAL, 16MM FAN, CoolingPULLEY, Starter Flywheel CompHonda gx240k1/u1edn2 engine Ignition Coil assy CAP ASSY., Noise Suppresson HOLDER, Stop Switch CordCORD, Stop Switch Coil ASSY., IgnitionHonda gx240k1/u1edn2 engine GOV. Control assy SPRING, Governor SPRING, Control AdjustingARM, Governor ROD, GovernorHonda gx240k1/u1edn2 engine Auto Throttle assy Solenoid Assy CAP, Choke LeverSPRING, Choke Return STAY, Solenoid ThrottleHonda gx240k1/u1edn2 engine Fuel Cock assy CUP, Fuel Strainer PACKING, Fuel Strainer CUPRing Filter CUPHonda gx240k1/u1edn2 engine Decal assy DECAL, AIR Cleaner DECAL, ChokeMARK, OIL Caution Honda gx240k1/u1edn2 engine Tool KIT BAG Tool Wrench COMP. Spark PlugHANDLE, BOX Wrench SapnnerFReighT pOlicY Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

GAC3.6HZ specifications

The Multiquip GAC3.6HZ is a highly efficient air-cooled generator designed to meet the energy demands of both residential and industrial applications. This generator showcases a perfect combination of performance, durability, and ease of use, making it a popular choice among contractors, event organizers, and homeowners alike.

One of the standout features of the GAC3.6HZ is its powerful Honda GX160 engine, known for its reliability and fuel efficiency. The engine delivers an impressive output of 3.6 kilowatts, making it suitable for a wide range of applications from powering tools on job sites to supplying electricity for small events. The generator's maximum power output ensures that it can handle heavy loads while maintaining consistent performance.

Equipped with a large-capacity fuel tank, the GAC3.6HZ provides extended operation without the need for frequent refueling. This makes it ideal for situations where access to fuel may be limited, such as remote job sites. Additionally, the generator features a low oil shutdown system that enhances engine longevity by automatically shutting down the engine in the event of low oil levels, protecting it from damage.

The GAC3.6HZ is designed with portability in mind. It includes a robust frame, built-in wheels, and a convenient lifting handle, allowing for easy transportation between locations. Its compact design also ensures that it can be stored in smaller spaces without hassle.

Another significant aspect of the GAC3.6HZ is its user-friendly control panel, which features clearly labeled outlets, including multiple 120V AC outlets and a 12V DC outlet for battery charging. The intuitive layout of the control panel simplifies operation, even for users who may not be familiar with generator functions.

Multiquip has incorporated advanced noise reduction technologies into the GAC3.6HZ, ensuring that it operates at lower noise levels compared to traditional generators. This is particularly beneficial for noise-sensitive environments, where quiet operation is essential.

In summary, the Multiquip GAC3.6HZ stands out as an exceptional generator owing to its robust Honda engine, fuel efficiency, extended run time, user-friendly design, and advanced noise-reduction features. Whether for commercial use or home backup, this generator provides reliable power when it is most needed, all within a compact and portable format.
Top Page Image Contents