Mega Catch Complete Guide to Mosquito Trap Manual
Page 15

Method Two:

1.Hang the Mega-Catch™ Mosquito Trap from the Stand (see Page 4 - Initial Set Up Instructions section - paragraph 11).

2.Slide the Skirt up from the bottom of the Trap (over 2 corners initially) with the elastic band at the top.

3.The Skirt is properly fitted when the elastic band is seated over the lower horizontal rib, just below the inlet holes (see figure 5). The opening in the Skirt should be located at the front of the Trap so as to facilitate removal of the Door without having to remove the Skirt. The hook-and-loop fastening on this opening should be closed when the Trap is running.

NOTE: Failure to position the skirt correctly will result in a NIL mosquito catch.

The Skirt is not manufactured from a U.V.-resistant material but this will not be an issue if the Trap is operated in shaded conditions as recommended. The Skirt can be reversed should one side begin to fade from exposure to U.V. light. The Skirt is a consumable item and replacements can be obtained from your Authorized Distributor.

Care of Your Trap

Your Mega-Catch™ Mosquito Trap requires very little maintenance. The Catch Bag and Liquid Catch Container should be cleaned and washed when required. Heavy catches of mosquitoes may result in a build-up of material in the internal casing and blade tips of the Fan. There may also be a build-up of material on the Fan Safety Guard. If this happens use the following cleaning technique:

1.Ensure the power to your Mega-Catch™ Mosquito Trap is disconnected. (Attention:

High-Speed Fan inside the Trap may cause injury if the power is not disconnected.)

2.To remove the Trap from the Stand, tip the Trap on its side and slide if off the hook.

3.Unlock and remove the Lockable Door. Then lay the Trap on its side with the Door opening being face up.

4.Reach inside the Trap and remove the Fan Safety Guard (attached to base of Fan) by turning it counterclockwise (see figure 6).

5.Using a small sponge or toothbrush and warm soapy water, reach into the Trap and carefully clean the inside casing of the Fan and the Fan Blades.

6.Ensure that water is not allowed to enter into the Fan Motor. Never hose water into the Fan.

7.Clean and then replace the Fan Safety Guard.

8.Leave the Trap to dry for at least 24 hours before reinstalling it on the Stand and recommencing operation.

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Mosquito Trap Contents Important Safety Instructions Introduction Features of Mega-Catch Premier Mosquito TrapInitial Set Up Instructions What Your Mega-Catch Mosquito Trap Will Do Then plug into the power supplyTrap Positioning Installing and Siting the Mega-Catch Mosquito TrapInstallation of Trap Initial Set Up Instructions sectionPage Trap Assembly Instructions Stand Assembly InstructionsMega Catch Operation of the Programmable TimerHow to Program Mega CatchThen Press Clock to Return to Normal Operation Mosquito Catching Systems Using the Liquid Catch ContainerFitting of Catch Bag Using the Catch BagFitting of External Skirt Method OneFitting External Skirt Method Two Care of Your TrapRemoval of Fan Safety Guard Replacement of U.V. BlubMega-Catch Octenol Fragrance Strip Placement Position for Mega-Catch Octenol Fragrance StripOptional Accessories Battery Terminal Power CableCigarette Lighter/Car Accessory Terminal Cable Opening the Trap refer to figure Maintenance and Repair of Your TrapRe-assembly of Trap Replacement of U.V. Bulb refer to figureReinstallation of Plates Connection of WiresOpening the Premier Trap To Remove the Timer Unit refer to figure Removal of TimerCan I stop my Mega-Catch Mosquito Trap from catching moths? Frequently Asked QuestionsHow often do I need to operate my Mega-Catch Mosquito Trap? Will Mega-Catch Mosquito Traps catch biting flies?Problem Solving Need Help? SpecificationsIf your Mega-Catch Mosquito Trap fails to operate Description Parts List
Top Page Image Contents