Master Lock MGR2900A, MGR4500I, MGR6000I installation manual Prestart, Starting

Page 11

OWNER’S MANUAL

OPERATION

Continued

PRESTART

Operate generator on a firm, dry, and clean surface. The surface must be level. Protect generator from heavy dust, sand, dirt, rain, or snow. Do not locate generator near standing water and snow. Make sure area is well-vented.

WARNING: Only responsible adults should use generator. Never let anyone operate genera- tor without proper instructions.

Note: If oil level is too low, oil alert system will keep engine from starting (see Oil Alert System, page 6). Make sure oil level is full before starting. See Engine Oil, page 7.

Before starting the engine, disconnect all electric loads from generator.

STARTING

IMPORTANT: The engine speed is preset. The throttle is locked in preset position. Do not adjust throttle. Preset position lets engine run at 3600 RPM under load. The engine

4.Start the engine.

Turn engine switch to the ON position (see Figure 12). Remove slack from starter rope by lightly pulling starter grip. Next, pull starter rope briskly.

IMPORTANT: Do not let starter grip snap back against engine. Return it gen- tly. This will prevent damage to starter.

Note: If engine does not start, check the oil in the crankcase. Add oil as necessary. Be sure engine is on a level surface. See Oil Alert System, page 6.

5.As engine warms up, slowly move choke lever fully to the right (see Figure 13) (all models except MGR6000I). This opens the choke. On Model MGR6000I, slowly push in choke button until fully depressed (see Figure 14).

Choke Lever (Closed Position)

ENGINE SW

ON

OFF

Figure 12 - Engine Switch In ON Position

Choke Lever (Open Position)

CLOSED

OPEN

Fuel Valve Lever (ON Position)

Figure 13 - Choke Lever Opened (Model MGR4500I Shown)

must maintain 3600 RPM for generator to create correct voltage. Running engine at lower speeds will damage generator and powered items.

IMPORTANT: Never start generator with electrical loads connected. Start engine before adding electrical loads.

1.Make sure gasoline tank is full. See Fuel, page 7 for fuel information.

2.Move fuel valve lever to the ON posi- tion except on Model MGR6000I (see Figure 10).

3.Move choke lever fully to the left for all models except MGR6000I (see Figure 10). Pull choke button out for Model MGR6000I (see Figure 11). This closes the choke.

Note: You may not need to close choke if engine is warm or air temperature is high.

 

CLOSED

Choke Lever (Open Position)

OPEN

 

 

Fuel Valve Lever (ON Position)

Figure 10 - Fuel Valve Lever On, Choke

Lever Closed (Model MGR4500I Shown)

Choke Lever (Closed Position)

Figure 14 - Choke Lever Opened (Model

MGR6000I Shown)

Figure 11 - Choke Lever Closed (Model

MGR6000I Shown)

Continued

118679

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Portable Gasoline Generators Portable Gasoline Generators Safety InformationIf it produces smoke or flames Product IdentificationVentilation High and LOW Temperature OperationGeneral Information UnpackingMGR2900A MGR4500I MGR6000I SpecificationsModel AUTO-IDLE System Generator FeaturesVoltage Selector Switch OIL Alert SystemChecking OIL Level and Adding OIL Engine OILFuel Receptacle Circuit BreakerGenerator Grounding Standby Installation to Home or BuildingRecommended Minimum Wire Gauges AWG for Extension Cords Extension CordsDetermining Electrical Load for Generator Chart 1 Typical Electric Appliance WattagesChart General Information Using ReceptaclePower Cord and Plug Requirements OperationStarting PrestartAUTO-IDLE Operation Adjusting the Idle Speed Models MGR4500I MGR6000IStopping Engine Maintenance and RepairsDisconnecting Electric Loads High Altitude Operation Adding Electrical LoadsServicing the Engine Technical ServiceTroubleshooting StorageModel Electrical Component SpecificationsWiring Diagrams CapacitorWiring Diagram, Models MGR4500I and MGR6000I Parts Available not Shown Illustrated Parts ListFor Model MGR2900A Alternator Assembly KEY Part Number Description QTYDescription QTY For Models MGR4500I MGR6000I Alternator AssemblyKEY Part Number for Model MGR4500I MGR6000IFor Model MGR2900A Roll Cage Inform For Models MGR4500I MGR6000I Fuel Tank Roll CageKEY For Models MGR4500I MGR6000I Fuel Tank and Roll CageFor Models MGR4500I MGR6000I Control Panel NON-WARRANTY Service Replacement Parts and AccessoriesRepair Service Warranty ServiceKeep this Warranty Warranty Information

MGR2900A, MGR4500I, MGR6000I specifications

Master Lock has long been synonymous with security, providing reliable and durable locks to ensure peace of mind. Among its diverse product range, the Master Lock MGR2900A, MGR4500I, and MGR6000I stand out due to their advanced features and design.

The Master Lock MGR2900A is a versatile combination padlock that offers convenience and security. With a customizable four-digit combination, users can enjoy the ease of access while maintaining privacy. Its solid steel construction ensures strength and durability, while a weather-resistant cover protects it from environmental factors, making it suitable for both indoor and outdoor use. The MGR2900A's compact size makes it ideal for securing lockers, gates, and storage units, providing users with a reliable locking solution in various scenarios.

Moving up in capability, the Master Lock MGR4500I is equipped with innovative technology designed to maximize security. This electronic bike lock employs a Bluetooth connection, allowing users to lock and unlock the device directly from their smartphones. The MGR4500I features a built-in alarm system that activates upon attempted tampering, deterring potential thieves. Its sturdy construction, combined with a rechargeable battery that can last for weeks, makes it a popular choice for cyclists. Additionally, the app provides access to usage history and alerts, giving users complete control over their lock's functionality.

Finally, the Master Lock MGR6000I exemplifies the pinnacle of electronic security. This smart lock integrates seamlessly with home automation systems, allowing users to control access remotely. Offering fingerprint recognition and smartphone connectivity, the MGR6000I ensures quick yet secure entry—ideal for busy households. Its sleek design complements modern aesthetics while providing robust security measures, including a backup key option for emergencies. The lock's weather-resistant features make it resilient against the elements, ensuring reliable performance year-round.

In summary, the Master Lock MGR2900A, MGR4500I, and MGR6000I each provide unique features suited for different security needs. From customizable combinations and Bluetooth connectivity to advanced smart technology, these locks exemplify Master Lock’s commitment to innovation and quality, making them ideal choices for anyone seeking dependability and peace of mind.
Top Page Image Contents