Land Pride DM36 Series manual Operating Instructions

Page 17

Land Pride

Section 2 Operating

Table of Contents

Operating Instructions

By now you should have thoroughly read your Disc Mower Operator’s Manual, properly attached your Land Pride Disc Mower to your tractor, and reviewed the Operating Checklist. If you have not yet completed all of these functions, please do so now.

Now that you’re properly briefed and your Disc Mower is ready, it’s time to transport to the field.

For transport purposes, your Disc Mower should be securely locked with the cutter bar in the upright or vertical position. Make sure the support leg is in the high position. A "Slow Moving Vehicle" sign should be in place and visible from the rear, if you are using a public road or right-of-way. Select a safe speed and transport to your cutting site in such manner that faster moving vehicles can pass you safely.

Once you have safely arrived at your field, position your tractor on level ground. Make sure that no one is within 20 ft of the mower, as your prepare to lower the cutter bar from transport to working position. Lower the three-point hitch to a point where the inboard end of the cutter bar is approximately 12" off of the ground. Retract your lift cylinder and pull on the latch cord to release the transport or road-latch mechanism. Using your lift cylinder control lever, slowly lower the cutter bar until the outer end touches the ground. Adjust the three-point hitch to "working position" where the driveline is horizontal with the ground and lock the three-point hitch control lever in place. Extend the lift cylinder until there is 1" of clearance over the reach arm. Your Disc Mower is now in working position.

Controlling or setting your cutting height is accomplished by adjusting the "top link" on your three-point hitch. Extending or lengthening the top link will raise your cutting height, while shortening the top link will lower the cutting height. If you are cutting in an area you are not familiar with or believe there might be rocks or debris present, you must raise the cutting height accordingly. This will reduce the potential of personal injury and or damage to the machine. Shut the mower down immediately if someone approaches in a vehicle or on foot.

If you do hit an object when you are mowing, immediately disengage the PTO, idle the engine, stop the tractor, wait for all moving parts to come to a complete stop, shut off the tractor, set the brake, remove the keys, and inspect for damage. If damage is present, make the necessary repairs. If no damage is present, but you have tripped the Break Away Safety Latch, slowly reverse the tractor until the latch resets and proceed with mowing operations.

Prior to actually beginning cutting operations, you will want to get the mower up to full 540 rpm PTO speed by engaging the PTO with the tractor engine at idle and gradually increasing engine rpm to PTO speed. Once you reach the full 540 rpm, allow the mower to run for a few minutes at level position so the oil in the cutter bar can lubricate all internal moving parts. You will also want to take this opportunity to make a quick Operational Running Check. Listen and visually inspect for any component or part that may be loose or out of adjustment. Don’t be alarmed by the noise level of the free running Disc Mower. It will actually become quieter when you begin mowing and have some run in time on it.

If your Operational Running Check was ok, begin mowing operations by opening up the lands on your field. Make enough lands so you can easily make your turns to properly line up for each pass down the field. If your tractor and Disc Mower are set up right, you should be able to straddle the previous swath as you make each subsequent pass starting in the center of the field. If you do experience cutting problems, refer to the "Trouble Shooting" section of the Operator’s Manual for corrective action.

When you are done mowing for the day and need to transport the mower to your storage site, simply reverse the process you used to take the mower out of transport mode. When you are done mowing for the season, clean and lubricate your mower, replace warn or missing parts, release tension on the belts, install the stroke control to the tarp frame cushion spring rod and store the unit with the cutter bar in the horizontal working position. You will get longer service life out of your mower by storing it inside and repainting scratched or rusted components.

With a little practice and experience you should become very good at operating your Land Pride Disc Mower.

5/5/08

DM36 Series Disc Mowers 327-045M

15

Image 17
Contents Disc Mowers Table of Contents Be Aware of Signal Words Practice Safe Maintenance Use Safety Lights and DevicesTransport Machinery Safely Tractors With Cabs Tractors Equipped WithSafety at All Times Tire SafetyPrepare for Emergencies Wear Protective Equipment818-552C 818-540C818-642C 838-094C 818-558C 818-543C Application Using This ManualOwner Assistance Land PrideMainframe Assembly Assembly PreparationTools Required Cutter Bar and Gearbox LubricationMain Frame Assembly Support Stand Assembly Belt Cover and Pulleys AssemblyCutting Unit Assembly Attaching the Tractor Spring Tension Adjustment for Spring AssemblyOperating Check List Operating ChecklistTransporting Adverse Field Conditions Working PositionMowing Instructions Operating Instructions Transport Lock Operation AdjustmentsPivot Bolt Tension Bolt Belt Tension AdjustmentCutting Height Servicing Blades General MaintenanceRemoval of disc shaft assemblies Cutter Bar Timing AdjustmentStorage Lubricate as noted in Maintenance and Lubrication onLubrication LubricationDriveline Driveline U-JointsHitch Pivot Point Cutter BarFrame Pivot Point DM3605 DM3606 DM3607 DM36 Series Disc MowersFeatures and Benefits Streaking conditions in swath Problem Cause Solution Not cutting cleanGearbox noisy Gearbox leakingBolt Head Identification Bolt Size 10.9 Inches Metric Torque Values Chart for Common Bolt SizesWarranty Corporate Office P.O. Box 5060 Salina, Kansas 67402-5060 USA

DM36 Series specifications

The Land Pride DM36 Series is a premium line of rotary mowers designed for durability, efficiency, and exceptional performance in demanding mowing conditions. These mowers are engineered to provide precise cutting and maintenance for a variety of environments, making them ideal for both professional landscapers and property owners seeking a reliable mowing solution.

One of the standout features of the DM36 Series is its heavy-duty construction. Built with a robust steel chassis, the mower is designed to withstand the rigors of frequent use while providing stability and control. The reinforced deck is fully welded, ensuring that it can handle rough terrain and obstacles without compromising its structural integrity.

The DM36 Series also boasts adjustable cutting heights ranging from 1 to 4 inches, allowing operators to customize their mowing experience based on the type of vegetation and field conditions. This versatility is complemented by the mower's efficient blade design, which includes high-quality blades specifically designed to create a clean cut and minimal discharge, resulting in a tidy appearance and healthier turf.

Equipped with advanced technology, the DM36 Series incorporates features that enhance operational efficiency. The mower is designed for compatibility with various tractors, allowing for smooth integration with existing equipment. Additionally, its quick-attach mounting system ensures easy installation and removal, streamlining the workflow for users.

For improved operator comfort, the DM36 series includes ergonomic handles and controls that are strategically placed for ease of use. The mower's design reduces vibration and noise, promoting a more enjoyable mowing experience, especially during extended use.

Another notable characteristic of the DM36 Series is its maintenance-friendly design. Regular servicing and maintenance are simplified thanks to accessible grease points and easily replaceable parts. This approach not only extends the life of the mower but also ensures it remains in top working condition with minimal downtime.

In summary, the Land Pride DM36 Series combines robust construction, adjustable cutting heights, advanced technology, and user-friendly design to provide an exceptional mowing experience. Whether you're maintaining large properties, parks, or commercial landscapes, the DM36 Series stands out as a trusted and effective solution for all mowing needs. With its commitment to quality and performance, Land Pride continues to be a leader in the rotary mower market.