Marantz SR5300 Programming with the 4-DIGIT Code, Scanning the Code Table, Checking the Code

Page 13
Switch on the appliance which should be controlled.

⁄7CLEAR button

This button is used to cancel for certain memory or programming operations.

⁄8DIMMER button

When this button is pressed once, the display is dimmed.

When this button is pressed twice, the display is turned off and the “DISPLAY OFF” indicator lights up.

Press this button again to turn on the display again.

⁄9NIGHT button

Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back.

When this button is pressed, “NIGHT” indicator lights up.

¤0S- ( Source) DIRECT button

When this button is pressed, the tone control circuit is bypassed as well as Bass Management.

¤1SETUP / T.TONE button

Test tone function is used for adjusting the balance between the volume levels of speaker channels. Press AMP button and press this button to enter the test tone mode.

¤2OSD button

When this button is pressed, the current setting are displayed on the TV monitor.

¤3SLEEP (sleep timer) button

This button is used for setting the sleep timer. It can be operated the same way as the button in unit.

¤4TV VOLUME UP () /DOWN () buttons

These buttons increase or decrease TV’s volume.

PROGRAMMING THE REMOTE CONTROLLER

The remote controller RC5300SR must be programmed to use the codes for your appliances of different brands. This is done by keying in a 4-digit code or by scanning the codes until the correct one is found. We recommend to using the 4-digit code. This mode is faster and more reliable. The code scanning method should be used only if you cannot find the code for one of your appliances. The codes are listed at the end of this book.

Important:

Use the remote control buttons for programming, not the buttons of the receiver or other appliances.

PROGRAMMING WITH THE 4-DIGIT CODE

1. Press and hold down the function button c for the appliance which should be controlled and press SETUP ¤1until the indicator z blinks twice.

2. Press the 4-digit code for appliance (code table at the end of this book)

3. When the procedure is successful, the indicator will blink twice.

Note:

If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

SCANNING THE CODE TABLE

1.

2. Press and hold down the function button c for appliance which should be controlled and press SETUP ¤1until the indicator z blinking twice.

3. Press the code 9 - 9 - 1.

The indicator will blink twice.

4. Aim the remote control at the appliance and slowly alternate between pressing POWER x and the function button c for the appliance.

5. Stop when the appliance turns off.

6. Press SETUP ¤1once to lock in the code.

CHECKING THE CODE

1. Press and hold down the function button c for appliance which should be controlled and press SETUP ¤1until the indicator z blinking twice.

2. Press the code 9 - 9 - 0. The indicator will blink twice.

3. To view the code for first digit, press 1 once.

Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the indicator will not blink.

4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.

ENGLISH

7

Image 13
Contents Model SR5300 User Guide Read Before Operating Equipment Important Safety InstructionsPage Risk of Electric Shock Risk of Electric Shock 5o!6!7!0 Table of Contents Description IntroductionBUILT-IN 6 Channel Power Amplifier FeaturesFront Panel Features see ¡8AC ¡7AC OutletFunction and Operation OperationInput Scanning the Code Table Programming with the 4-DIGIT CodeChecking the Code Remote Control Operation of Remote Control UnitLoading Batteries Connections Speaker PlacementHeight of the Speaker Units Connecting Speaker Wire Connecting SpeakersConnecting Banana Plug Connecting a SubwooferConnecting Digital Audio Components Connecting Audio ComponentsVIDEO, S-VIDEO Jacks Connecting Video ComponentsVideo jack Connecting Remote Control Jacks Advanced ConnectingConnecting Multi Channel Audio Source Connecting External Power AmplifierConnecting the Supplied Antennas Connecting the Antenna TerminalsConnecting AN FM Outdoor Antenna Connecting AN AM Outdoor AntennaOn Screen Display Menu System SetupSpeaker Size Speaker SetupSpeakers Level Speaker Distance Time AlignmentSurround PreferencePL2 PRO Logic II Music Parameter CH Input Level CS2 Circle Surround II ParameterListening to the Tuner Basic OperationPlayback Operation Setting the Sleep TimerTV Auto ON/OFF Function S C R E E N D I S P L a Y Infomation Surround Mode Source Direct StereoSurround Input Signal Format Status & Surround Mode Temporary Display Status Symptom Cause Remedy Trouble ShootingMemory backup HOW to Reset the UnitGeneral Malfunction Dimension Technical SpecificationsSetup Codes 0120 VCR DVD Is a registered trademark