Jonsered 630, 625, 670 manual Basic cutting technique, General, Terms, Cutting

Page 20

SAFETY INSTRUCTIONS

2 Basic cutting technique

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke.

See the section on ”How to avoid kickback” to find out why cutting on the push stroke increases the risk of kickback.

Terms:

Cutting

=

General term for cutting through wood.

Limbing

=

Cutting limbs off a felled tree.

Splitting

=

When the object you are cutting breaks off

 

 

before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the bar will not jam in the cut.

2Make sure the log will not split.

3 Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kick- back?

5Do the conditions and surrounding terrain affect your safety when working?

Two factors decide whether the chain will jam or the log will split. The first is how the log is supported and the second is whether it is in tension.

In most cases you can avoid these problems by cutting in two stages; from the top and from the bottom of the log. You need to support the log so that it will not trap the chain or split during cutting.

!If the chain jams in the cut:

STOP THE ENGINE! Don’t try to pull the saw free. If you do you may damage the chain when the saw suddenly breaks free. Use a lever to open up the cut and free the bar.

The following instructions describe how to handle most types of situation that you will be faced with when using a chain saw.

Cutting

1 The log is lying on the ground. There is little risk of the chain jamming or the log splitting. However there is a risk that the chain will touch the ground when you finish the cut.

Cut all the way through the log from above. Try not to touch the ground as you finish the cut. Maintain full throttle but be prepared in case the chain snatches.

A If it is possible to turn the log you should stop cutting about 2/3 of the way through.

B Turn the log and finish the cut from the opposite side.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Operator´s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the chain saw Contents Safety Instructions Personal Protective EquipmentChain brake and front hand guard Right hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking brake band wear Checking the front hand guardChecking the automatic brake Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesCutting equipment designed to minimise kickback BarSaw chain Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance Lubricating cutting equipment Chain oilFilling with chain oil Never use waste oilChecking chain lubrication Lubricating the clutch drum bearingChecking wear on cutting equipment Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles Min m 10 ftProlonged inhalation of exhaust gases from Engine, chain lubrication oil mist and/orBasic safety rules General Working InstructionsBasic cutting technique GeneralTerms CuttingTree felling technique Safe distanceLimbing Felling directionClearing the trunk and preparing your retreat FellingGeneral advice Freeing a tree that has fallen badly = high accident riskCutting the trunk into logs Freeing a Trapped treeWhat is WHAT? What is what?Fitting a spike bumper AssemblyMounting guide bar and chain Chain oil Fuel HandlingFuelmix Fuelling Start and Stop Start and stopMaintenance CarburettorStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterSilencer Spark plugWinter use Temperature -5C or colderCooling system Weekly maintenance Daily maintenance Monthly maintenanceBar and chain combinations Technical Data625 630 670 Page 108 87

630, 670, 625 specifications

The Jonsered 625, 670, and 630 chainsaws represent a robust line of products designed specifically for both professional and amateur users who require reliability, power, and efficiency in their cutting tasks. These models are a testament to Jonsered's commitment to innovation and performance in the forestry and outdoor equipment sector.

The Jonsered 625 features a compact design, making it ideal for users who need a lightweight tool for trimming, pruning, or cutting smaller trees. This model is equipped with a powerful engine that delivers an impressive power-to-weight ratio, enabling users to handle tough jobs without feeling fatigued. One of the standout features of the 625 is its ergonomic design, including a comfortable handle and optimized balance, which significantly reduces operator strain during extended use.

Meanwhile, the Jonsered 670 is tailored for those who need a bit more power and capacity. It is versatile enough to handle medium-sized cutting tasks as well as heavy-duty use. This model is designed with advanced vibration dampening technology, minimizing vibrations transferred to the user's hands, thus enhancing comfort and precision. The 670 also incorporates the Easy Start system, which makes starting the saw simple, even after long periods of inactivity.

The Jonsered 630 stands at the higher end of this trio, aimed at professional users who demand peak performance. With an increased engine size and enhanced cutting speed, the 630 can tackle larger trees and tougher materials with ease. This model features a high-performance air filtration system that ensures the engine remains clean and runs efficiently. Additionally, the 630 incorporates a centrifugal air cleaning system that prolongs service intervals and reduces maintenance needs.

All three models come equipped with cutting-edge technologies such as the X-Torq engine, which lowers fuel consumption and exhaust emissions, making them environmentally friendly options in today's market. These chainsaws incorporate safety features like chain brakes and low kickback chains, ensuring user safety during operation.

In summary, the Jonsered 625, 670, and 630 chainsaws each offer distinct advantages catering to various user needs, from homeowners tackling light-duty tasks to professionals requiring robust, high-performance machinery. The blend of technology, ergonomic design, and safety ensures that Jonsered continues to be a trusted name in outdoor power equipment. These chainsaws not only deliver superior cutting performance but also provide a seamless user experience.
Top Page Image Contents