Jonsered Essential Chainsaw Fuel Mixture and Specifications Guide

Page 26

FUEL HANDLING

Fuelmix

IMPORTANT! The chain saw is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

!Always provide for good ventilation when handling fuel.

Petrol

• Use good quality unleaded or leaded petrol.

• The lowest octane recommended is 90.

• If you run the engine on a lower octane grade than 90 so-called, knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.

When working with continuous high revs (e.g. delimbing) a higher octane grade is recommended.

Two-stroke oil

For the best results use JONSERED two-stroke oil, which is especially developed for chain saws. Mixing ratio 1:50 (2%).

If JONSERED two-stroke oil is not available, you may use another two-stroke oil of good quality that is intended for air cooled engines. Contact your dealer when selecting an oil. Mixing ratio 1:33 (3%)-1:25 (4%).

Never use two-stroke oil intended for water cooled outboard motors, so-called, outboard oil.

Never use oil intended for four-stroke engines.

Gasolin

 

Oil • Öl

 

Benzin

 

Huile • Aceite

 

Essence

 

Lit.

 

Gasolina

 

 

2%(1:50) 3%(1:33) 4%(1:25)

Lit.

5

0,10

0,15

0,20

10

0,20

0,30

0,40

15

0,30

0,45

0,60

20

0,40

0,60

0,80

US

 

US

 

gallon

 

fl. oz.

 

 

2%(1:50) 3%(1:33) 4%(1:25)

1

2 1/2

3 3/4

5 1/8

2 1/2

6 1/2

9 3/4

12 7/8

5

12 7/8

19 1/4

25 3/4

26 – English

 

 

 

Mixing

Always mix the petrol and oil in a clean container intended for fuel.

Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

Mix (shake) the fuel mixture thoroughly before filling the saw’s fuel tank.

Do not mix more than approx. 1 month supply of fuel.

If the saw is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

The chain lubrication system is automatic. Always use special chain oil with good adhesive characteristics.

In countries where no special chain oil is available, EP 90 transmission oil can be used.

Never use waste oil. This results in damage to the oil pump, the bar and the chain.

It is important to use oil of the right viscosity according to the air temperature.

In temperatures below 0oC (32oF) some oils become less viscous. This can overload the oil pump and result in damage to the oil pump components.

Contact your servicing dealer when choosing chain oil.

Image 26
Contents Operator´s manual Symbols in the operator’s manual KEY to SymbolsSymbols on the chain saw Contents Safety Instructions Personal Protective EquipmentChain brake and front hand guard Right hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Tensioning the chain General advice on setting raker clearanceSetting the raker clearance Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?Never use the saw one- handed General rulesDo not let go of the handles Prolonged inhalation of exhaust gases from Min m10 ft Engine, chain lubrication oil mist and/orBasic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? What is what?Fitting a spike bumper AssemblyMounting guide bar and chain Chain oil Fuel HandlingFuelmix Fuelling Start and Stop Start and stopMaintenance CarburettorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springSilencer Needle bearing maintenanceAir filter Spark plugWinter use Temperature -5C or colderCooling system Weekly maintenance Daily maintenance Monthly maintenanceBar and chain combinations Technical Data625 630 670 Page 108 87

630, 670, 625 specifications

The Jonsered 625, 670, and 630 chainsaws represent a robust line of products designed specifically for both professional and amateur users who require reliability, power, and efficiency in their cutting tasks. These models are a testament to Jonsered's commitment to innovation and performance in the forestry and outdoor equipment sector.

The Jonsered 625 features a compact design, making it ideal for users who need a lightweight tool for trimming, pruning, or cutting smaller trees. This model is equipped with a powerful engine that delivers an impressive power-to-weight ratio, enabling users to handle tough jobs without feeling fatigued. One of the standout features of the 625 is its ergonomic design, including a comfortable handle and optimized balance, which significantly reduces operator strain during extended use.

Meanwhile, the Jonsered 670 is tailored for those who need a bit more power and capacity. It is versatile enough to handle medium-sized cutting tasks as well as heavy-duty use. This model is designed with advanced vibration dampening technology, minimizing vibrations transferred to the user's hands, thus enhancing comfort and precision. The 670 also incorporates the Easy Start system, which makes starting the saw simple, even after long periods of inactivity.

The Jonsered 630 stands at the higher end of this trio, aimed at professional users who demand peak performance. With an increased engine size and enhanced cutting speed, the 630 can tackle larger trees and tougher materials with ease. This model features a high-performance air filtration system that ensures the engine remains clean and runs efficiently. Additionally, the 630 incorporates a centrifugal air cleaning system that prolongs service intervals and reduces maintenance needs.

All three models come equipped with cutting-edge technologies such as the X-Torq engine, which lowers fuel consumption and exhaust emissions, making them environmentally friendly options in today's market. These chainsaws incorporate safety features like chain brakes and low kickback chains, ensuring user safety during operation.

In summary, the Jonsered 625, 670, and 630 chainsaws each offer distinct advantages catering to various user needs, from homeowners tackling light-duty tasks to professionals requiring robust, high-performance machinery. The blend of technology, ergonomic design, and safety ensures that Jonsered continues to be a trusted name in outdoor power equipment. These chainsaws not only deliver superior cutting performance but also provide a seamless user experience.