Jonsered CS 2186 manual Air filter, Muffler, Needle bearing maintenance, Spark plug

Page 31

MAINTENANCE

Air filter

The air filter must be regularly cleaned from dust and dirt in order to avoid:

•Carburetor malfunctions

• Starting problems

• Engine power reduction

• Unnecessary wear on the engine parts

• Abnormal fuel consumption

Clean the air filter daily or more often if the air is exceptionally dusty in the working area.

• Disassemble the air filter by removing the air filter-cover and unscrew the filter.

When reassembling, make sure that the filter is tight against the filter holder. Clean the filter by brushing or shaking it.

Muffler

The muffler is designed in

order to reduce the noise level and to direct the exhaust

gases away from the operator.

The exhaust gases are hot and can contain sparks, which

may cause fire if directed against dry and combustible

material. Some mufflers are equipped with a special screen.

If your saw has this type of muffler, you should clean the screen at least once a week. This is done with a wire brush.

CAUTION! The screen must be replaced, if damaged. The saw will be overheated, if the screen is clogged. This results in damage on the cylinder and the piston. Never use a saw with a clogged or defective muffler.

Needle bearing maintenance

•A more thorough cleaning of the filter is obtained by washing it in water and

soap.

An air filter, which is used for some time, cannot be cleaned completely. Therefore it must be replaced by a new one, with regular intervals.

IMPORTANT! A damaged air filter must always be replaced.

Spark plug

The spark plug condition is influenced by:

The clutch drum is equipped with one of the following chain sprockets:

•Spur sprocket (A) (the chain sprocket is welded on the drum)

•Rim sprocket (B) (exchangeable)

Both versions have buit-in needle bearing at the drive shaft, whitch has to be greased regularly (once a week).

NOTE! Use only high quality bearing grease or engine oil.

A

B

•

An incorrect carburetor setting.

•

Wrong fuel mixture (too much oil in the gasoline).

Adjustment of the oil pump

• A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties.

If the engine is low on

0,5 mm

power, difficult to start or

 

runs poorly at idling speed,

 

always check the spark plug

 

first. If the spark plug is dirty,

 

clean it and check the

 

electrode gap. Readjust if

 

necessary. The correct gap is

 

0,5 mm (0,020"). The spark

 

plug should be replaced after

 

The oil pump is adjustable. Ad- justments are made by turning the screw using a screwdriver or combination spanner. The saw is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

–

+

about a month in operation or

earlier if the electrodes are

badly eroded.

IMPORTANT! Always use the recommended spark plug type. An incorrect spark plug can severely damage the piston/cylinder.

WARNING! The engine must not be running when making adjustments.

Recommended settings:

Bar -15": 1 turn from the closed position.

Bar 15"-18": 2 turns from the closed position.

Bar 18"-24": 3 turns from the closed position.

Bar 24"- : 4 turns from the closed position.

These recommendations apply to Jonsered’s chain oil, for other chain oil increase the oil flow by one step.

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Operator´s manual Symbols KEY to SymbolsContents Personal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardChain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethSetting the raker clearance General advice on setting raker clearanceTensioning the chain Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Checking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesNever use the saw one- handed 10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is what? What is WHAT?Mounting guide bar and chain AssemblyFuelmix Fuel HandlingMin 3 m Fuelling10ft Stop Start and StopStart and stop StartCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordMuffler Needle bearing maintenanceAdjustment of the oil pump Air filterElectrically heated carburetor CS 2186WH Centrifugal cleaning Air InjectionCooling system Heated handles CS 2186WMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data + 46 36 14 65 00. Warranty Period Emission Control Warranty Statement+ 46 36 14 65 2002W21 108 88

CS 2186 specifications

The Jonsered CS 2186 is a versatile chainsaw designed to meet the needs of both professional and recreational users. Known for its robust performance and user-friendly features, this saw showcases great engineering and innovative technology.

One of the standout features of the CS 2186 is its powerful engine. Incorporating a 50.2 cc engine, it delivers an impressive power output that allows smooth cutting through wood of varying densities. This engine is designed with modern technology to ensure efficient fuel consumption, reducing emissions without compromising performance.

The chainsaw is equipped with a 16 to 20-inch bar, providing options for different cutting applications. Whether for tree felling, limbing, or firewood preparation, the adjustable bar length makes the CS 2186 a flexible choice suited for a variety of tasks. The specific chain design promotes an excellent cutting experience, combining sharpness and durability.

Comfort and ease of use are also priorities for the Jonsered CS 2186. The chainsaw features an ergonomic handle with anti-vibration technology, which minimizes fatigue during prolonged use. Users can work longer and with more control, enhancing overall safety and precision in cutting.

Another noteworthy technology is the Easy Start system, which significantly reduces the effort needed to start the engine. This is especially beneficial for those who may struggle with traditional starting methods. Additionally, the chainsaw includes an automatic oiler that ensures proper lubrication of the chain, contributing to both efficiency and longevity of the equipment.

Safety is paramount in chainsaw design, and the CS 2186 incorporates multiple safety features. It includes a chain brake that acts immediately in case of kickback, preventing serious injuries. The front-hand guard and throttle lock further enhance safety by providing additional protection and control.

Overall, the Jonsered CS 2186 stands out for its blend of power, innovative technologies, and user-focused design. This chainsaw represents an excellent investment for anyone in need of a reliable, efficient, and safe cutting tool capable of performing a variety of jobs effectively. Whether you're a landowner, professional lumberjack, or simply enjoy working with wood, the CS 2186 is a commendable choice that exemplifies quality and performance in the world of chainsaws.
Top Page Image Contents