Jonsered LT2218A manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents LT2218A General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Seat Unassembled PartsSteering Wheel Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Check Battery See FigCheck Tire Pressure Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor Throttle Control Used to control engine speedStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Stop Mower BladesTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelAutomatic Transmission Warm UP To Start Engine See FigPurge Transmission Mowing Tips Maintenance General RecommendationsBlade Care BatteryTractor Blade Removal See FigTransaxle Pump Fluid Transaxle MaintenanceEngine BeltsAIR Filter CleaningClean AIR Screen MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigTo Check Brake Replacing Battery See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Jonsered Motor AB

LT2218A specifications

The Jonsered LT2218A is a reliable, high-performance lawn tractor designed for residential use, delivering exceptional cutting efficiency and user comfort. This model is particularly favored by homeowners with medium to large-sized lawns due to its robust features and easy operability.

One of the standout features of the LT2218A is its powerful 18 hp engine, which ensures a smooth and strong performance even on challenging terrains. The engine is paired with a hydrostatic transmission that allows for seamless speed adjustments without the need for manual shifting. This feature provides excellent maneuverability, allowing the operator to focus on the task at hand while maintaining control over the speed.

The cutting deck of the Jonsered LT2218A is designed for versatility and precision. It boasts a 42-inch cutting width with a stamped steel construction, ensuring durability and a clean cut. This deck is equipped with multiple cutting height adjustments, ranging from 1 to 4 inches, which enables users to customize their mowing experience according to varying grass lengths and conditions.

Another notable characteristic of this lawn tractor is its ergonomic design, which emphasizes user comfort. The adjustable seat and easy-grip steering wheel contribute to an enjoyable riding experience, reducing operator fatigue during longer mowing sessions. Additionally, the tractor is equipped with a simple control panel that allows for easy access to all essential functions, ensuring that users can operate the machine without unnecessary complexity.

The Jonsered LT2218A also features advanced technologies such as the Clean Out Port, which facilitates easy cleaning of the cutting deck after use, helping to maintain optimal performance. Moreover, the tractor's durable chassis ensures stability and longevity, making it a sound investment for homeowners.

For those looking for a practical, efficient, and user-friendly lawn tractor, the Jonsered LT2218A stands out as an excellent choice. With its strong engine, versatile cutting options, and user-centered design, it promises to make lawn care a more enjoyable and effective task for any homeowner.
Top Page Image Contents