Jonsered LT2218A Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use

the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1)

3/4" wrench

Pliers

(2)

7/16" wrenches

Tire pressure gauge

(1)

5/16" wrench

 

(1)

1/2" wrench

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dashed lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

TO INSTALL STEERING WHEEL (See Fig. 1)

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, lock washer, hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSTALL SEAT (See Figs. 2 and 3)

•Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

•Connect switch to seat.

•Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

ASSEMBLE EXTENSION SHAFT AND BOOT

 

• Slide extension shaft onto lower steering shaft.

SEAT

• Place tabs of steering boot over tab slots in dash and

SWITCH

push down to secure.

 

INSERT

PAD

 

HEX BOLT

 

LOCK WASHER

SLOT

LARGE FLAT

SEAT

WASHER

 

PAN

STEERING

 

WHEEL

TAPE

 

 

WIRING HARNESS

STEERING BOOT

 

 

Fig. 2

ADAPTER

•Push down on seat to engage pads in slots and pull seat towards rear of tractor.

EXTENSION SHAFT

LOWER

STEERING

SHAFT

•Raise seat and tighten bolt securely.

•Remove tape and discard.

•Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

To adjust seat: Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

Fig. 1

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents LT2218A General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Seat Unassembled PartsSteering Wheel Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Deck Levelness To Check Battery See FigCheck Tire Pressure Check for Proper Position of ALL BeltsChecklist Operation Know Your Tractor Throttle Control Used to control engine speedStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Stop Mower BladesTowing Carts and Other Attachments Before Starting the EngineTo Operate on Hills Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips Maintenance General RecommendationsBlade Care BatteryTractor Blade Removal See FigTransaxle Pump Fluid Transaxle MaintenanceEngine BeltsAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig Replacing Battery See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXService Notes Service Notes Jonsered Motor AB

LT2218A specifications

The Jonsered LT2218A is a reliable, high-performance lawn tractor designed for residential use, delivering exceptional cutting efficiency and user comfort. This model is particularly favored by homeowners with medium to large-sized lawns due to its robust features and easy operability.

One of the standout features of the LT2218A is its powerful 18 hp engine, which ensures a smooth and strong performance even on challenging terrains. The engine is paired with a hydrostatic transmission that allows for seamless speed adjustments without the need for manual shifting. This feature provides excellent maneuverability, allowing the operator to focus on the task at hand while maintaining control over the speed.

The cutting deck of the Jonsered LT2218A is designed for versatility and precision. It boasts a 42-inch cutting width with a stamped steel construction, ensuring durability and a clean cut. This deck is equipped with multiple cutting height adjustments, ranging from 1 to 4 inches, which enables users to customize their mowing experience according to varying grass lengths and conditions.

Another notable characteristic of this lawn tractor is its ergonomic design, which emphasizes user comfort. The adjustable seat and easy-grip steering wheel contribute to an enjoyable riding experience, reducing operator fatigue during longer mowing sessions. Additionally, the tractor is equipped with a simple control panel that allows for easy access to all essential functions, ensuring that users can operate the machine without unnecessary complexity.

The Jonsered LT2218A also features advanced technologies such as the Clean Out Port, which facilitates easy cleaning of the cutting deck after use, helping to maintain optimal performance. Moreover, the tractor's durable chassis ensures stability and longevity, making it a sound investment for homeowners.

For those looking for a practical, efficient, and user-friendly lawn tractor, the Jonsered LT2218A stands out as an excellent choice. With its strong engine, versatile cutting options, and user-centered design, it promises to make lawn care a more enjoyable and effective task for any homeowner.
Top Page Image Contents