Jonsered CS 2250S KEY to Symbols, Symbols on the machine, Symbols in the operator’s manual

Page 2

KEY TO SYMBOLS

Symbols on the machine:

WARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others.

Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.

Always wear:

•Approved protective helmet

• Approved hearing protection

• Protective goggles or a visor

Both of the operator′s hands must be used to operate the chain saw.

Never operate a chain saw holding it with one hand only.

Never let the guide bar tip come in contact with any object.

Tip contact may cause the guide bar to move suddenly upward and backward (so-called kickback), which may cause serious injury.

Other symbols/decals on the machine refer to special certification requirements for certain markets.

Symbols in the operator’s manual:

Switch off the engine before carrying out any checks or maintenance. CAUTION! The

start/stop switch automatically returns to run position. In order to prevent unintentional

starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or performing maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

2 – English

Visual check.

Protective goggles or a visor must be worn.

Refuelling.

Filing with oil and adjusting oil flow.

The chain brake must be engaged when the chain saw is started.

You will find the following labels on your chain saw:

EPA II

The Emissions Compliance Period referred to on the Emission Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emissions requirements. Category C = 50 hours, B = 125 hours, and A = 300 hours.

Maintenance, replacement, or repair of the emission control devices and system may be performed by any nonroad engine repair establishment or individual.

The engine exhaust from this product contains chemical known to the State of California to cause cancer, birth defects or other reproductive harm.

Page 1 Page 3
Image 2
Page 1 Page 3
Contents CS 2245S Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping system Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment CS 2245S, CS 2250SChain drive sprocket Filling with chain oilChecking chain lubrication Needle bearing lubrication Checking wear on cutting equipmentWorking with the chain AssemblyFitting the bar and chain Assembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Checking the inertia brake release Muffler Tensioning the recoil spring StarterReplacing the starter cord Fitting the starter Air filterReplacing the return and drive springs Needle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemWinter use Turbo Air Cleaning centrifugal cleaningTemperature -5C 23F or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data058/1,5 mm Bar and chain combinations050/1,3 mm Saw chain filing and file gauges Federal Emission Control Warranty Statement Repair or Replacement of Parts Repair orKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1151012-95
Top Page Image Contents