Jonsered CS 2245S, CS 2250S manual Federal Emission Control Warranty Statement

Page 42

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

dealer. If you have any questions regarding your warranty

OBLIGATIONS

rights and responsibilities, you should contact your nearest

authorized servicing dealer or call Jonsered, at Sweden

The EPA (The US Environmental Protection Agency),

+46-36-146500.

Environment Canada and Jonsered are pleased to explain

WARRANTY PERIOD Any warranted part which is not

the emissions control system warranty on your 2001 and

scheduled for replacement as required maintenance, or

later small nonroad engine. In U.S. and Canada, new small

which is scheduled only for regular inspection to the effect

nonroad engines must be designed, built and equipped to

of “repair or replace as necessary” shall be warranted for 2

meet the federal stringent anti-smog standards. Jonsered

years. Any warranted part which is scheduled for

must warrant the emission control system on your small

replacement as required maintenance shall be warranted

nonroad engine for the period of time listed below provided

for the period of time up to the first scheduled replacement

there has been no abuse, neglect or improper maintenance

point for that part.

of your unit. Your emmission control system includes Parts

DIAGNOSIS The owner shall not be charged for diagnostic

such as the carburetor and the ignition system. Where a

labor which leads to the determination that a warranted

warrantable condition exists, Jonsered will repair your small

part is defective, if the diagnostic work is performed at an

nonroad engine at no cost to you. Expenses covered under

approved Jonsered servicing dealer.

warranty include diagnosis, parts and labor.

CONSEQUENTIAL DAMAGES Jonsered may be liable for

 

damages to other engine components caused by the

MANUFACTURER S WARRANTY

failure of a warranted part still under warranty.

COVERAGE

WHAT IS NOT COVERED

The 2001 and later small nonroad engines are warranted

for two years. If any emission related part on you engine

All failures caused by abuse, neglect or improper

(as listed above) is defective, the part will be repaired or

maintenance are not covered.

replaced by Jonsered.

ADD -ON OR MODIFIED PARTS

OWNER S WARRANTY RESPONSIBILITIES

The use of add-on or modified parts can be grounds for

As the small nonroad engine owner, you are responsible for

disallowing a warranty claim. Jonsered is not liable to cover

failures of warranted parts caused by the use of add-on or

the performance of the required maintenance listed in your

modified parts.

Operators Manual. Jonsered recommends that you retain all

 

receipts covering maintenance on your small nonroad

HOW TO FILE A CLAIM

engine, but Jonsered cannot deny warranty solely for the lack

If you have any questions regarding your warranty rights and

of receipts or for your failure to ensure the performance of all

responsibilities, you should contact your nearest authorized

scheduled maintenance. As the small nonroad engine owner,

servicing dealer or call Jonsered, at Sweden +46-36-146500.

you should, however, be aware that Jonsered may deny you

WHERE TO GET WARRANTY SERVICE

warranty coverage if your small nonroad engine or a part of it

has failed due to abuse, neglect, improper maintenance,

Warranty services or repairs shall be provided at all

unapproved modifications or the use of parts not made or

Jonsered authorized servicing dealers.

approved by the original equipment manufacturer. You are

MAINTENANCE, REPLACEMENT AND

responsible for presenting your small nonroad engine to a

Jonsered authorized servicing dealer as soon as a problem

REPAIR OF EMISSION-RELATED PARTS

exists. The warranty repairs should be completed in a

Any Jonsered approved replacement part used in the

reasonable amount of time, not to exceed 30 days. If you

performance of any warranty maintenance or repairs on

have any questions regarding your warranty rights and

emission-related parts, will be provided without charge to

responsibilities, you should contact your nearest authorized

the owner if the part is under warranty.

servicing dealer or call Jonsered, at Sweden +46-36-146500.

EMISSION CONTROL WARRANTY PARTS

WARRANTY COMMENCEMENT DATE

LIST

The warranty period begins on the date small nonroad

1 Carburetor and internal parts

engine is delivered.

2 Intake pipe, airfilter holder and carburetor bolts.

LENGTH OF COVERAGE

3 Airfilter and fuelfilter covered up to maintenance

Jonsered warrants to the initial owner and each

schedule.

subsequent purchaser that the engine is free from defects

4 Spark Plug, covered up to maintenance schedule

in materials and workmanship which cause the failure of a

5 Ignition Module

warranted part for a period of two years.

MAINTENANCE STATEMENT

WHAT IS COVERED

The owner is responsible for the performance of all required

REPAIR OR REPLACEMENT OF PARTS Repair or

maintenance, as defined in the operator’s manual.

replacement of any warranted part will be performed at no

 

charge to the owner at an approved Jonsered servicing

 

´®z+S!=¶57¨

´®z+S!=¶57¨

42 – English

Image 42
Contents CS 2245S Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain sawContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping system Stop switchCutting equipment MufflerCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment CS 2245S, CS 2250SFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainWorking with the chain Assembly Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLog is supported at one end. There is a high risk Tree felling techniqueLimbing Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cut How to avoid kickback What is kickback?Freeing a tree that has fallen badly Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Checking the inertia brake release Muffler Starter Replacing the starter cordTensioning the recoil spring Air filter Replacing the return and drive springsFitting the starter Needle bearing lubrication Spark plugLubricating the bar tip sprocket Cooling systemTurbo Air Cleaning centrifugal cleaning Temperature -5C 23F or colderWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations 050/1,3 mm058/1,5 mm Saw chain filing and file gauges Federal Emission Control Warranty Statement Repair or Replacement of Parts Repair orKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautions1151012-95