Jonsered CS 2240 manual Ignition module and flywheel Refitting

Page 28

Repair instructions

7.8 Ignition module and flywheel

– refitting

1

Fit the flywheel on the crankshaft journal. Turn the flywheel so that the key lines up with the keyway in the shaft.

Fit the nut on the shaft and tighten to a torque of 25-30 Nm (see figure 11).

Fig 11

2

To refit the ignition module proceed as follows:

Turn the flywheel so that the magnets are in line with the ignition module. Fit the ignition module with the plastic feeler gauge (502 51 34- 02) held in position at the same time, without tightening the bolts. Fit the earth cable (black) (A). Set a distance of 0.3 +/- 0.1 mm, between the ignition module and magnet. The measurement applies to the two lowest lugs on the ignition module. Tighten the screws, tightening torque 4.5–6 Nm. Fit the blue cable on the ignition module (see figure 12).

3

Then refit:

• cable guide and press the leads into position

• HT lead

• starter assembly, tighten to a torque of 2.5–3.5 Nm

• cylinder cover

Fig

12

When replacing the cables, they are fitted on the stop switch as shown in middle figure on the pre- vious page.

English – 29

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Workshop manual 510 16Workshop manual Jonsered CS 2240 and CS 2240S Contents Index Trouble shooting Vibration damping systemIntroduction and safety instructions ContentsSafety Target group GeneralChanges ToolsGeneral instructions Special instructionsSymbols on the saw Symbols in the Workshop ManualTechnical data Rpm Special tools 13a 13b 16b 16c 16a Service data Service data Safety equipment ContentsCleaning and inspection Dismantling the chain brakeChain brake reassembly Silencer removal Silencer refittingOperating test RefitChain catcher replacement Dismantling the start/stop controlStop switch resistance measurement Assembling the start/stop control2xA a Throttle lock, throttle trigger and return spring removalThrottle lock, throttle trigger and return spring refitting Repair instructions Starter assembly removal Changing a broken or worn starter cord Tensioning the recoil springIgnition module testing Starter assembly refittingReplacing a worn recoil spring Ignition module and flywheel Removal Ignition module and flywheel Refitting Centrifugal clutch removal Centrifugal clutch refitting Dismantling the oil pump and screenAssembling the intake system Assembling the oil pump and screenAir intake system removal Carburettor DesignFunction Dismantling the carburettor English Cleaning and inspection Clean all units in clean petrol Assembly Pressure testing the carburettor Assemble on the saw Replacement of the H-needle or complete car Burettor Carburettor adjustment Conditions during adjustmentReplacement of the L-needle Tank unit Venting the fuel tankTest Opening pressure outward Opening pressure inwardCleaning and inspection Clean and inspect all parts Assembly Vibration damping systemReplacing the fuel filter Replacing the fuel hose/ return hoseReplacing the air-purge AssemblingPiston and cylinder removal If replacing the cylinderEnglish Faults and causes Score marks on the piston a Piston and cylinder refittingCarbon build-up B Piston ring breakageInlet manifold Assembling the intake systemCylinder pressure testing Crankshaft bearings replacement Crankshaft complete dismantlingCrankshaft complete reassembly Repairing damaged threadsReplacing the front bar guide Replacing the bar boltReplacing the rear bar guide Troubleshooting Starting TroubleshootingIdling low rpm High rpm Troubleshooting methodsAcceleration och retardation 2009W39

CS 2240 specifications

The Jonsered CS 2240 is a powerful and versatile chainsaw designed for homeowners, landscapers, and property maintenance professionals. It stands out in the market due to its unique combination of performance-oriented technology, ergonomic design, and ease of use.

One of the main features of the Jonsered CS 2240 is its robust engine. With a 40.9cc X-Torq® engine, this chainsaw is designed to provide efficient power and performance while minimizing fuel consumption and emissions. The X-Torq® engine technology not only enhances the chainsaw's acceleration and torque but also contributes to better fuel efficiency, making it an environmentally friendly option for users.

The CS 2240 is equipped with a 16-inch bar, which strikes a perfect balance for various cutting tasks, whether it's felling small trees, trimming branches, or performing general maintenance. This length also allows for greater maneuverability in tight spaces, making it an ideal choice for homeowners and professional users alike.

A notable aspect of the Jonsered CS 2240 is its innovative starting system. The Quick Release Air Filter ensures that the air filter can be easily accessed for maintenance, promoting optimal engine performance. Coupled with the Air Injection system, which filters out larger debris before it enters the engine, this chainsaw maintains a longer lifespan and reduces the frequency of required maintenance.

Safety is paramount in chainsaw design, and Jonsered does not compromise on that front. The CS 2240 features a chain brake, which halts the chain movement in the event of kickback. Additionally, the front handguard provides an extra layer of protection, ensuring that users can operate the saw with confidence.

The ergonomic design of the CS 2240 incorporates a comfortable handle that reduces vibrations, allowing for extended use without excessive fatigue. Weighing approximately 10.8 lbs, it strikes the right balance between power and portability.

In summary, the Jonsered CS 2240 is an excellent choice for those seeking a reliable, efficient, and user-friendly chainsaw. Its advanced engine technology, balanced bar length, safety features, and ergonomic design make it a standout in its class, ideal for tackling a variety of cutting tasks with ease and efficiency. Whether you are a casual user or a professional, the CS 2240 is well-equipped to meet diverse cutting needs while ensuring safety and comfort.
Top Page Image Contents