Marantz SR6200 manual ¤6Input system selector buttons, Video Input, ¤7SOURCE Power button

ENGLISH	¤6Input system selector buttons/
	FUNCTION SELECTOR buttons (AUDIO/
	VIDEO INPUT)
	Press one of these buttons once or twice to select a particular source
	component. For example, to set the amplifier or receiver to the DVD
	input, press the DVD button ¤6twice within 2 seconds.

Note:

CDR/MD button is set CDR function at initial. To switch MD function, press and hold down CDR/MD button and press 2 button b.

To return CDR function, press and hold down CDR/MD button and press 1 button b.

¤7SOURCE POWER button

Press to switch the power of an individual source component ON or OFF.

For example, to turn on the DVD player, first press the DVD button ¤6 then press the SOURCE POWER button ¤7.

Note:

All of the MARANTZ components equipped with D-BUS (RC-5) connection use the same power ON and OFF commands.

As a result, simply pressing the source power button of the remote control unit also allows you to turn the power of the components ON and OFF.

LEARNING METHOD

This remote control unit (RC6200SR) can learn, or program in itself, the remote control code of any function preset under any button of the remote control unit of any system component, except for the MAIN POWER and the FUNCTION buttons of the RC6200SR. The functions of the components that can be controlled through the D-BUS (RC-5) need not be learned, but the functions of other components must be learned before they can be controlled from the RC6200SR remote control unit. To let the RC6200SR learn the remote control code of a function of a component, follow the learning procedure described below.

1.Set the mode switch x to LEARN.

2.Select the component with the codes to be learned, by pressing one of the input selector buttons.

For example, when the CD button is pressed, most of the buttons on the remote control unit get ready to learn the CD control codes.

3.On the RC6200SR, press the button corresponding to the function to be learned. For example, if the function to be learned is playback, press the PLAY () button on the remote control unit. The LEARN indicator will light up.

4.Place the remote control unit of the component with the function to be learned at a distance of about 20 cm (8 inches) from the RC6200SR, so that the head (transmitting side) of the former remote control unit points the head of the RC6200SR.

5.On the remote control unit of the component, press and hold the button of the function to be learned, until the learning indicator of the RC6200SR starts to blink then goes off. The learning operation is complete when the indicator is extinguished.

6.Set the mode switch to USER.

7.Let the RC6200SR learn other codes by repeating the steps above for each code.

OK		NO GOOD
Top View		Top View	RC6200SR
DVD remote	RC6200SR	DVD remote
control unit		control unit	3	6	9
			2	5	8
			1	4	7
	3	6
	2	5
	1	4
Side View		Side View	RC6200SR
DVD remote	RC6200SR
control unit
5 cm		DVD remote
		control unit

Note:

When the system mode switch is in the USER position, the buttons which have not learned any function output the D-BUS (RC-5) codes when they are pressed. In the RC-5 (D-BUS) position, all buttons output the D-BUS (RC-5) codes.

FUNCTIONS THAT CAN BE LEARNED

The RC6200SR has buttons that can LEARN to 1, 4 or 10 types of different codes.

See the chart on the next page for the types of codes that can be learned by each button.

RECALLING THE PRESET FUNCTION

Even after a button has learned the remote control code of a function, its originally preset, D-BUS (RC-5) code can be recalled any time by following the procedure below.

1.Set the mode switch to LEARN.

2.Press the MAIN POWER OFF button and the button which has learned a function simultaneously.

3.Set the mode switch to USER.

Learning button indications

Although the learning buttons can be used to operate various components, the indications printed above the buttons are Marantz D- BUS (RC-5) preset code indications. To make it easier to remember which buttons perform which operations, therefore, we recommend that you program operations into buttons having the same or similar indications.

There are some situations where programming is not possible. In the following instances, both the TX and LEARN LEDs blink to indicate that programming cannot be carried out.

1.When the remote control unit’s memory is full.

2.When you attempt to program a command from a remote control unit using a different signal transmission format.

CLEARING ALL OF THE LEARNED CODES

Use the following procedure to reset all of the buttons which have learned remote control codes and make them possible to output RC-5 preset codes.

1.Set the mode switch to LEARN.

2.Hold down the MAIN POWER ON and OFF buttons simultaneously for more than 3 seconds. The TX and LEARN LED will blink and goes off.

3.Set the mode switch to USER.

8