Marantz SR6200 manual Speakers Setup, Spkr Setup 2/3 Spkr Distance, Spkr Setup 1/3 Spkr Size

SPEAKERS SETUP

The home theater system you already have installed should function provided that there are left, center and right front speakers, left and right rear/surround speakers and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units. This will deliver smooth pans across the front sound stage as the action moves from side to side.

Your center channel speaker is very important as over 80 % of the dialog from a typical motion picture emanates from the center channel. It should possess similar sonic characteristics to the main speakers.

Surround channel speakers need not be identical to the front channel speakers, but they should be of high quality.

The surround center speaker is useful for playback of Dolby Digital Surround EX or DTS-ES. One of the benefits of both Dolby Digital (AC-3) and DTS is that surround channels are discrete full range, while they were frequency limited in earlier “Pro Logic’ type systems. Bass effects are an important part of home theater. For optimal enjoyment a subwoofer should be used as it is optimized for low frequency reproduction. If you have full range front speakers, however, they may be used in place of a subwoofer with proper setting of the switches in the menu system.

SUB WOOFER

FRONT -L/R :Select the type of front speakers with	or	button.	ENGLISH
CENTER : Select the type of center speaker with	or	button.
SURR-L/R :Select the type of surround speakers with	or	button.

SURR.CENTER : Select the surround center speaker YES or NO with or button.

SUBWOOFER: Select the subwoofer speaker YES or NO with or

button.

Notes:

The SUBWOOFER cannot be set to NO when the front speakers are set to SMALL.

This speaker size setup is not effective when the SOURCE- DIRECT or 7CH. Input is selected.

SPKR SETUP 2/3 (SPKR DISTANCE)

LEFTRIGHT

CENTER

SURROUND-L SURROUND-R

SURROUND CENTER

If possible, mount the surround speakers on the walls to the sides of the viewing area, 2-3 feet above seated viewers, firing straight across at each other.

SPKR SETUP 1/3 (SPKR SIZE)

Use this parameter to specify the distance of the speaker’s position from the listener.

The delay time is automatically set according to these distances.

UNITS: You can select Meters or Feet.

If you select “ft”, the setting parameter will change in 1 foot steps.

If you select “m”, it will change in 0.3 meter steps.

Select speaker with	or button, and input each speaker’s
distance with or	button.

When the input for each speaker’s distance has been finished, move the cursor to ENTER and press the OK button.

NOTES :

If your selection(s) are out of range, the distance cannot be stored. Placement beyond that distance is beyond the range of the automatic time delay feature.

The delay feature does not function in the SOURCE-DIRECT ,7 CH-Input modes and decoding of 96 kHz sources.

SETUP: Select “LOCKED” with or button in order to lock the contents of the SPKR SET UP MENU.

When you want to change the contents of this setup, select “UNLOCKED”.

SPKR SIZE

This menu enters the information about which type of speakers will be used for each channel.

In turn, these settings will determine which speakers receive low frequency information.

For the purpose of establishing proper bass reproduction, use the LARGE settings if the speaker being used at any position is a traditional full-range loudspeaker that is capable of reproducing sound below 100 Hz and you are not using a subwoofer.

Use the SMALL setting for smaller, frequency-limited speakers that are not able to reproduce sounds below 100Hz and you are using a subwoofer. Low frequencies will be diverted from the speaker to the subwoofer.

Note that when “small” speakers are used it is advisable to install a separate subwoofer, especially if you wish to appreciate the full impact of a good home theater soundtrack.

If the Surround speakers or Center speaker will not be used, set NONE for each speaker. The NONE setting will send the audio for the channel to other speakers.

SPKR SETUP 3/3 (SPKR LEVEL)

�

SPKR LEVEL

TEST MODE: Selects the mode for generating the test tone.

If you select AUTO, the test tone will be cycled through in a circular pattern which is Left → Center → Right → Surround Right → Surround Center → Surround Left → Subwoofer → Left → ... 3 seconds for each channel.

If you select MANUAL, press the OK button to select the test tone channels after the “TEST TONE ON”.

TEST TONE: Press the	or	button, ON is indicated and the test
tone starts from the front L-CH speaker.
Press the	or	button again on this item. OFF is

indicated and the output of the test tone will stop. Channel: Adjust the level of test tone for each channel with the or

buttons of the RC6200SR. The current volume level is shown at the center of the display.

13