Husqvarna 1365GN owner manual Connecting Electrical Loads, Stopping the Engine, Charging a Battery

Page 9

Operation

4.Start engine according to instructions given in engine owner’s manual.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device. See engine manual.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator” on page 13.

Stopping the Engine

1.Unplug ALL electrical loads from generator panel receptacles. NEVER start or stop engine with electrical devices plugged in and turned ON.

2.Move idle control switch to “Off” position.

3.Let engine run at no-load for several minutes to stabilize internal temperatures of engine and generator.

4.Turn engine off according to instructions given in the engine owner’s manual.

5.Move fuel valve to “Off” position.

Operating Automatic Idle Control

This switch is designed to greatly improve fuel economy. When this switch is turned ON, the engine will only run at its normal high governed engine speed when an electrical load is connected.When an electrical load is removed, the engine will run at a reduced speed. With the switch off, the engine will run at the normal high engine

speed. Always have the switch off when starting and stopping the engine.

Charging a Battery

Your generator has the capability of recharging a discharged 12 Volt automotive or utility style storage battery. DO NOT use the unit to charge any 6 Volt batteries. DO NOT use the unit to crank an engine having a discharged battery.

DANGER

Storage batteries give off explosive hydrogen gas during recharging.

Hydrogen gas stays near battery for a long time after battery has been charged.

Slightest spark will ignite hydrogen and cause explosion.

You can be blinded or severely injured.

Battery electrolyte fluid contains acid and is extremely caustic.

Contact with battery fluid will cause severe chemical burns.

•DO NOT allow any open flame, spark, heat, or lit cigarette during and for several minutes after charging a battery.

•Wear protective goggles, rubber apron, and rubber gloves.

To recharge 12 Volt batteries, proceed as follows:

1.Check fluid level in all battery cells. If necessary, add ONLY distilled water to cover separators in battery cells. DO NOT use tap water.

2.If battery is equipped with vent caps, make sure they are installed and are tight.

3.If necessary, clean battery terminals.

4.Connect battery charge cable connector plug to panel receptacle identified by the words “12-VOLTS D.C.”.

5.Connect battery charge cable clamp with red handle to the positive (+) battery terminal (Figure 5).

Figure 5 — Battery Connections

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 1365GN Table of Contents Safety RulesEquipment Description Generator produces powerful voltage Unintentional sparking can result in fire or electric shock Volt DC,10 Amp Receptacle Recharge a discharged Know Your GeneratorVolt AC, 20 Amp Gfci Duplex Receptacles 120/240 Volt AC, 30 Amp Locking Receptacle MayCarton Contents AssemblyInstall Wheel Kit Remove Generator From CartonBefore Starting EngineAdd Engine Oil and Fuel Grounding Generator Operating GeneratorStarting the Engine Charging a Battery Connecting Electrical LoadsStopping the Engine Operating Automatic Idle ControlPermanent Cold Weather Shelter Cold Weather Operation120/240 Volt AC, 30 Amp, Locking Receptacle ReceptaclesVolt AC, 20 Amp, Gfci Duplex Receptacles Volt DC, 10 Amp ReceptacleTesting the Gfci Ground Fault ProtectionDont Overload Generator Power ManagementCapacity ExampleGeneral Maintenance Recommendations SpecificationsEngine Maintenance Generator CleaningStorage Generator StorageEngine Storage Other Storage Tips Page Troubleshooting Schematic Wiring Diagram Exploded View Main Unit Parts List Main Unit DescriptionParts Not Illustrated Exploded View and Parts List Alternator Exploded View and Parts List Control Panel Exploded View and Parts List Wheel KIT About your equipment warranty Equipment Consumer Use Commercial Use Pressure WasherPortable Generator

1365GN specifications

The Husqvarna 1365GN is a robust and highly efficient chainsaw designed for both professional users and serious enthusiasts. Built with innovation in mind, this model is particularly suited for demanding environments, combining power, durability, and user-friendly features that make it stand out in the market.

One of the main features of the Husqvarna 1365GN is its powerful engine, which delivers impressive performance for a variety of cutting tasks. With a high displacement engine, the chainsaw offers exceptional torque and cutting speeds, making it ideal for felling large trees, limbing, and heavy-duty cutting operations. The engine is designed to be fuel-efficient, helping users save on fuel costs while reducing emissions, adhering to modern environmental standards.

The 1365GN is equipped with advanced technologies that enhance its usability and performance. The AutoTune feature automatically adjusts the fuel-air mixture for optimal performance in different operating conditions, ensuring the machine runs smoothly regardless of the altitude, temperature, or fuel quality. This self-adjusting technology not only simplifies starter adjustments but also contributes to maintaining engine efficiency and longevity.

Another notable characteristic of the Husqvarna 1365GN is its ergonomic design. The chainsaw features an anti-vibration system that significantly reduces vibrations experienced by the operator, enabling extended use without discomfort. The lightweight construction ensures ease of handling, while the comfortable grip allows for better control during operation, providing safety and precision.

Safety is paramount in any power tool, and the Husqvarna 1365GN is fitted with several safety features that protect users during operation. The chain brake system is designed to stop the chain immediately in the event of a kickback, preventing potential accidents. Additionally, the chainsaw includes a low kickback bar and chain, enhancing overall safety without compromising cutting efficiency.

In terms of maintenance, the 1365GN is designed for easy access to key components, facilitating quick and hassle-free servicing. The air filter can be easily accessed and replaced, ensuring that the engine remains clean, which is vital for optimal performance and longevity.

Overall, the Husqvarna 1365GN exemplifies quality and reliability, being a perfect choice for those seeking a powerful, efficient, and safe chainsaw. Whether you're a professional logger or a tree care specialist, this chainsaw offers performance and features that meet the rigorous demands of any cutting task.
Top Page Image Contents