Homelite UT74121A manual Fuel and Refuelling, Handling the Fuel Safely, Mixing the Fuel

Page 12

OPERATION

WARNING:

Always turn off engine before refuelling. Never add fuel to a machine with a running or hot engine. Move at least 9 m (30 ft.) from refuelling site before starting the engine. DO NOT SMOKE! Failure to heed this warning can result in possible personal injury.

FUEL AND REFUELLING

HANDLING THE FUEL SAFELY

WARNING:

Check for fuel leaks. If any are found, correct them before using the saw to prevent fire or burn injury.

Always handle fuel with care; it is highly flammable. Always refuel outdoors and do not inhale fuel vapour. Do not let petrol or oil come in contact with skin.

Keep petrol and oil away from the eyes. If petrol or oil comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately.

Clean up spilled fuel immediately.

MIXING THE FUEL

This product is powered by a 2-cycle engine and requires pre-mixing petrol and 2-cycle oil. Pre-mix unleaded petrol and 2-cycle engine oil in a clean container approved

for petrol.

This engine is certified to operate on unleaded petrol intended for motor vehicle use with an octane rating of 87 ([R + M] / 2) or higher.

Do not use any type of pre-mixed petrol/oil from fuel service stations. This includes the pre-mixed petrol/oil intended for use in mopeds, motorcycles etc.

Use a high quality 2-cycle self-mixing oil for air-cooled engines. Do not use motor vehicle oil or 2-cycle outboard oil.

Mix 2% oil into the petrol. This is a 50:1 ratio.

Mix the fuel thoroughly and each time before refuelling.

Mix in small quantities. Do not mix quantities larger than usable in a 30-day period. A 2-cycle oil containing a fuel stabiliser is recommended.

FILLING THE TANK

Refer to “Specific Safety Rules – Refuelling” earlier in this manual for additional safety information.

1.Clean the surface round fuel cap to prevent contamination.

2.Loosen the fuel cap slowly.

3.Carefully pour the fuel mixture into the tank. Avoid spillage.

See Figure 8.

4.Before replacing the fuel cap, clean and inspect the gasket.

5.Immediately replace the fuel cap and hand tighten. Wipe up any fuel spillage.

NOTE: It is normal for the engine to emit smoke during and after the first use.

1 Litre

+

20 ml

=

}

 

2 Litres

+

40 ml

=

50:1

3 Litres

+

60 ml

=

4 Litres

+

80 ml

=

 

5 Litres

+

100 ml

=

 

 

UK - Page 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsDo not Operate a Chainsaw That is Damaged Specific Safety Rules General PrecautionsSafety Apparel Basic Precautions in the CUTTING/ Work AreaMaintenance Precautions Push and PullKICK-BACK Pull PushSymbols Symbol Name ExplanationRUN StopSpecifications Features Understanding Your Chainsaw Safety Devices OperationLOW KICK-BACK SAW Chain Guide BarsKICK-BACK Precautions Chain BrakeRUN Position KICK-BACK Brake Position RotationalFuel and Refuelling Handling the Fuel SafelyMixing the Fuel Filling the TankBrake Position Ignition Switch RUN Primer Bulb Chain OIL SystemStarting the Engine See Figures 10 toStarting a Cold Engine Stopping the Engine Starting a Warm EnginePreparing for Cutting Proper Grip on HandlesChain Line Proper GripBasic OPERATING/CUTTING Procedures Work Area PrecautionsAdjusting the Carburettor See Figures 24Adjusting Idling Speed Operating the Chain BrakeBrake Position RUN Position Felling Trees Hazardous Conditions Retreat PathProper Procedure for Tree Felling Planned Line of FallRetreat Hinge Notch Approx /3 Diameter Trunk Back CUTHinge Back CUT WedgeRemoving Buttress Roots BuckingBucking with a Wedge Vertical CUT Loose Section Horizontal KICK-BACK WedgeBucking Logs Under Stress OverbuckingUnderbucking LOG Supported AT ONE END Finishing CUTLimbing and Pruning Cutting Spring PolesLoad Second CUT Finishing CUT Spring PoleMaintenance Assembling the BAR and ChainCutters Chain Tensioning Screw Adjusting the Chain Tension Chain MaintenanceSee Figures 52, 53 Flats on Drive LinksSharpening the Cutters Check for Wear or Damage LEFT-HAND Cutters RIGHT-HAND Maintaining Depth Gauge Clearance TOP Plate Filing AngleSide Plate Angle Restore Original Shape by Rounding Front Maintaining the Guide BARMaintaining the SAFE-T-TIP Nose Guard Lubricating HoleCleaning the AIR Filter Mounting the SAFE-T-TIP Nose GuardTighten 3/4 Turn See Figures 71, 72Cleaning the Starter Unit Cleaning the EngineChecking the Fuel Filter Replacing the Sparking PlugCleaning the Spark Arresting SI- Lencer Chain Catcher Brake Band Clean the Chain BrakeChain Brake Storing the Chainsaw 1 Month or LongerTroubleshooting Problem Possible Cause SolutionBAR and Chain Combinations Tions. See Figure But chain is not rotatingWarranty Safety DirectiveGuarantee Statement Rtsa / Rtuk / RTG EC Declaration of ConformityPage Ryobi Technologies GmbH

UT74121A specifications

The Homelite UT74121A is a versatile gas-powered string trimmer designed for homeowners and landscapers seeking an efficient tool for maintaining their lawns and gardens. Known for its reliability, the UT74121A combines performance with user-friendly features that make lawn care tasks less daunting.

One of the standout features of the UT74121A is its powerful 26cc 2-cycle engine. This engine provides ample power for cutting through dense grass and weeds, ensuring that tasks are completed quickly and efficiently. The lightweight design of the trimmer, coupled with its ergonomic handle, allows users to maneuver easily, making it ideal for extended use without causing fatigue.

The Homelite UT74121A is equipped with an easy-to-load bump feed spool for quick line replacement. Users can effortlessly advance the cutting line by tapping the trimmer's head on the ground, making it convenient to maintain the desired cutting length without interrupting work. The trimmer uses .095-inch diameter line, which provides durability and resilience against tough conditions.

In terms of design, the UT74121A features a straight shaft that offers increased reach and allows users to access hard-to-reach areas with ease. This design is particularly helpful for trimming along fences, in flower beds, and under low-hanging branches. The adjustable handle height further enhances user comfort, allowing for customization based on individual preferences.

Safety is a primary concern for any outdoor equipment, and the UT74121A incorporates several features to enhance user safety. It comes with a protective shield that prevents debris from being thrown during operation, and the easy-starting system reduces pull effort, making it accessible for users of all skill levels.

The trimmer also adheres to stringent emissions standards, making it an environmentally-friendly option in today's market. With proper maintenance, the UT74121A ensures longevity and sustained performance, making it a valuable addition to any landscaping toolkit.

Overall, the Homelite UT74121A is a powerful and efficient solution for those seeking a reliable string trimmer. Its combination of a robust engine, user-centric design, and safety features makes it suitable for various lawn care tasks, ensuring gardens and lawns remain well-groomed year-round.
Top Page Image Contents