Homelite UT10942D manual Stopping the Engine, Trigger Release Throttle Trigger, See Figures 20

Page 13

OPERATION

CHOKE LEVER

Fig. 18

7. When the temperature is above 50° F, pull the STARTER GRIP until the engine attempts to start, but no more than 3 times. When the temperature is below 50° F, pull the STARTER GRIP until the engine attempts to start, but no more than 5 times.

8.Push CHOKE lever all the way IN. See Figure 18.

9.Pull the STARTER GRIP until engine runs.

Note: Allow the saw to run in this position 15-30 seconds depending upon the temperature.

10.SQUEEZE and release the throttle trigger to return the engine to idle.

CAUTION:

Failure to release partial throttle when chain brake lever is in the brake position will result in serious damage to the unit. Never squeeze and hold the throttle trigger while the chain brake is in the brake position.

TRIGGER

RELEASE

THROTTLE TRIGGER

Fig. 19

Now you are ready to pick up the saw. Use the proper grip for both handles, refer to “Operation” for additional information.

STOPPING THE ENGINE

See Figures 20 and 21.

Release the throttle trigger and let the engine return to idle. To stop the engine, move the Ignition Switch to the

“O ” stop position. Do not put the chain saw on the ground when the chain is still moving. For additional safety, set the chain brake when the saw is not in use.

In the event that the Ignition Switch will not stop the saw, pull the choke lever out to the fully extended position (See Figure 17) and engage chain brake to stop the engine.

If the Ignition Switch will not stop the saw when set to the stop “ O ” position, have the Ignition Switch repaired before using the chain saw again to prevent unsafe conditions or serious injury.

Important: When you are finished using the saw, relieve tank pressures by loosening the CHAIN OIL and FUEL MIX caps. Then retighten the caps. Allow the engine to cool before storing.

IGNITION SWITCH

IN THE STOP

POSITION

Fig. 20

BRAKE POSITION

Fig. 21

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Save this Manual for Future Reference Operators ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesGeneral Precautions Specific Safety RulesSafety Apparel Refueling do not SmokePush and Pull Maintenance PrecautionsKickback See FigureSymbol Name Explanation SymbolsUT10946D SpecificationsFeatures Operation Understanding Your Chain SAW Safety DevicesChain Brake See Figures 4Fuel and Refueling Kickback PrecautionsSee Figures 6 Handling the Fuel SafelyOperating the Chain Brake Adding OILSee Figures 9 See Figures 10, 11Starting the Engine Starter Grip Ignition Switch RUN PositionSee Figures 13 through RUN Position Primer Bulb Choke LeverStopping the Engine Ignition Switch Stop Position Brake PositionTrigger Release Throttle Trigger See Figures 20Proper Grip on Handles Preparing for CuttingSee Proper Grip Chain LineWork Area Precautions Basic OPERATING/CUTTING ProceduresAdjusting the Carburetor See Figures 26Felling Trees Adjusting Idle SpeedSee Figures 30, 31, 32, Proper Procedure for Tree FellingHinge Back CUT Wedge Bucking Removing Buttress RootsBucking with a Wedge Vertical CUT Loose Section Horizontal Kickback WedgeLOG Supported AT ONE END Finishing CUT Bucking Logs Under StressCutting Springpoles Limbing and PruningAssembling the BAR and Chain MaintenanceSee Figures 41 through Cutters Chain Drive Links BAR Groove BAR Studs Adjusting PINGuide BAR Plate SprocketChain Tensioning Screw Chain Maintenance Adjusting the Chain TensionSee Figures 52, 53, Flats on Drive LinksSee Figures 57, 58, 59, 60, Sharpening the CuttersLeft Hand Cutters Right Hand TOP Plate Filing Angle Maintaining Depth Gauge ClearanceSide Plate Angle See , 65,Maintaining the SAFE-T-TIPNOSE Guard Maintaining the Guide BARSee Figures 68 Mounting the SAFE-T-TIP Nose Guard Cleaning the AIR FilterTighten 3/4 Turn See Figures 70, 71,Cleaning the Engine Cleaning the Starter UnitChecking the Fuel Filter Replacing the Spark PlugChain Catcher Clutch Cover Brake Band Clean the Chain Brake Cleaning the Spark Arresting MufflerStoring the Chain SAW 1 Month or Longer Spark Arrestor Screen Nuts MufflerProblem Possible Cause Solution TroubleshootingBAR and Chain Combinations Troubleshooting Limited Warranty Statement WarrantyHomelite Consumer PRODUCTS, INC

UT10942D specifications

The Homelite UT10942D is a powerful and versatile string trimmer designed for both residential and commercial landscaping needs. With its lightweight construction and user-friendly features, it provides an ideal solution for maintaining a pristine garden or lawn. One of the standout qualities of the UT10942D is its robust 25cc, 2-cycle engine that delivers ample power while remaining efficient. This engine enables users to tackle thick weeds and overgrown grass with ease.

One of the primary features of the UT10942D is its easy-start technology, which significantly reduces the effort needed to fire up the machine. This function is especially valuable for those who may struggle with traditional starting methods, ensuring a smooth and hassle-free user experience. The bike handle configuration enhances control and maneuverability, allowing users to navigate various terrains effortlessly.

Equipped with a dual-line feeding system, the trimmer allows for faster cutting, helping users to complete their tasks in less time. The 18-inch cutting swath provides an extensive coverage area, making it well-suited for both small and large properties. Additionally, the bump feed mechanism simplifies line advancement, enabling users to focus on their work without interruptions.

The Homelite UT10942D also boasts a durable construction, designed to withstand the rigors of frequent use. Its heavy-duty parts are built to last while still being lightweight, reducing fatigue during extended sessions. Furthermore, the inclusion of an adjustable cutting head enhances versatility, allowing users to switch between trimming and edging functions easily.

For added convenience, the trimmer comes with an anti-vibration feature that decreases hand fatigue, making it comfortable to operate for prolonged periods. Safety features, including a guard to protect the user from debris and a secure grip handle, are also part of the design, ensuring a safer cutting experience.

In summary, the Homelite UT10942D is a reliable and efficient string trimmer that combines power and ease of use. Its innovative technologies and thoughtful features make it a popular choice among homeowners and professionals alike, providing a truly effective tool for lawn care and maintenance. Whether for maintaining a small garden or taking care of larger landscapes, the UT10942D is equipped to handle the challenge, delivering precise results every time.
Top Page Image Contents