Homelite UT10942D Cleaning the Spark Arresting Muffler, Storing the Chain SAW 1 Month or Longer

Page 32

MAINTENANCE

CLEANING THE SPARK ARRESTING MUFFLER

See Figure 78.

The muffler is equipped with a spark arrestor screen. A faulty spark arrestor screen can create a fire hazard. Through normal use the screen can become dirty and should be inspected weekly and cleaned as required. Always keep the muffler and spark arrestor on your saw in good condition.

WARNING

Muffler surfaces are very hot during and after operation of the chain saw, keep all body parts away from the muffler. Serious burns may occur if contact is made with the muffler.

1.Allow the muffler to cool.

2.The spark arrestor screen is retained by the deflector. Remove the nuts and screen retainer to access the spark arrestor screen.

3.Replace the spark arrestor screen if it is cracked or otherwise deteriorated.

SPARK ARRESTOR

SCREEN

NUTS MUFFLER

Fig. 78

CHAIN BRAKE

See Figures 79 and 80.

■Remove the clutch cover and clean the chain brake components. Check wear on the brake band and replace if worn or deformed. The band thickness should not be less than 0.024 in. (.60 mm), or worn halfway through.

■Always keep the chain brake mechanism clean and lightly lubricate the linkage.

■Always test the chain brake performance after servicing or cleaning. Refer to “Operation - Operating Chain Brake” earlier in this manual for additional information.

■Check and, if damaged, replace the chain catcher.

CHAIN CATCHER

CLUTCH

COVER

BRAKE BAND

Fig. 79

CLEAN THE CHAIN BRAKE

LUBRICATE THE CHAIN

BRAKE LINKAGE

 

Fig. 80

STORING THE CHAIN SAW (1 MONTH OR LONGER)

1.Drain all fuel from tank into a container approved for gasoline.

2.Run the engine until it stops. This will remove all fuel-oil mix that could become stale and leave varnish and gum in the fuel system.

3.Drain all bar and chain oil from tank into a container approved for oil.

4.Clean all foreign material from the saw.

5.Store it in a well-ventilated place that is inaccessible to children.

Note: Keep away from corrosive agents such as garden chemicals and deicing salts.

Abide by all federal and local regulations for the safe storage and handling of gasoline. Excess fuel can be used in other 2-cycle engine powered equipment requiring 50:1 ratio.

Page 32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules General PrecautionsSafety Apparel Refueling do not SmokeMaintenance Precautions Push and PullKickback See FigureSymbols Symbol Name ExplanationSpecifications UT10946DFeatures Understanding Your Chain SAW Safety Devices OperationChain Brake See Figures 4Kickback Precautions Fuel and RefuelingSee Figures 6 Handling the Fuel SafelyAdding OIL Operating the Chain BrakeSee Figures 9 See Figures 10, 11Starter Grip Ignition Switch RUN Position Starting the EngineSee Figures 13 through RUN Position Primer Bulb Choke LeverIgnition Switch Stop Position Brake Position Stopping the EngineTrigger Release Throttle Trigger See Figures 20Preparing for Cutting Proper Grip on HandlesSee Proper Grip Chain LineBasic OPERATING/CUTTING Procedures Work Area PrecautionsAdjusting the Carburetor See Figures 26Adjusting Idle Speed Felling TreesProper Procedure for Tree Felling See Figures 30, 31, 32,Hinge Back CUT Wedge Removing Buttress Roots BuckingBucking with a Wedge Vertical CUT Loose Section Horizontal Kickback WedgeBucking Logs Under Stress LOG Supported AT ONE END Finishing CUTLimbing and Pruning Cutting SpringpolesSee Figures 41 through MaintenanceAssembling the BAR and Chain Chain Drive Links BAR Groove BAR Studs Adjusting PIN CuttersGuide BAR Plate SprocketChain Tensioning Screw Adjusting the Chain Tension Chain MaintenanceSee Figures 52, 53, Flats on Drive LinksSharpening the Cutters See Figures 57, 58, 59, 60,Left Hand Cutters Right Hand Maintaining Depth Gauge Clearance TOP Plate Filing AngleSide Plate Angle See , 65,See Figures 68 Maintaining the Guide BARMaintaining the SAFE-T-TIPNOSE Guard Cleaning the AIR Filter Mounting the SAFE-T-TIP Nose GuardTighten 3/4 Turn See Figures 70, 71,Cleaning the Starter Unit Cleaning the EngineChecking the Fuel Filter Replacing the Spark PlugCleaning the Spark Arresting Muffler Chain Catcher Clutch Cover Brake Band Clean the Chain BrakeStoring the Chain SAW 1 Month or Longer Spark Arrestor Screen Nuts MufflerBAR and Chain Combinations TroubleshootingProblem Possible Cause Solution Troubleshooting Warranty Limited Warranty StatementHomelite Consumer PRODUCTS, INC

UT10942D specifications

The Homelite UT10942D is a powerful and versatile string trimmer designed for both residential and commercial landscaping needs. With its lightweight construction and user-friendly features, it provides an ideal solution for maintaining a pristine garden or lawn. One of the standout qualities of the UT10942D is its robust 25cc, 2-cycle engine that delivers ample power while remaining efficient. This engine enables users to tackle thick weeds and overgrown grass with ease.

One of the primary features of the UT10942D is its easy-start technology, which significantly reduces the effort needed to fire up the machine. This function is especially valuable for those who may struggle with traditional starting methods, ensuring a smooth and hassle-free user experience. The bike handle configuration enhances control and maneuverability, allowing users to navigate various terrains effortlessly.

Equipped with a dual-line feeding system, the trimmer allows for faster cutting, helping users to complete their tasks in less time. The 18-inch cutting swath provides an extensive coverage area, making it well-suited for both small and large properties. Additionally, the bump feed mechanism simplifies line advancement, enabling users to focus on their work without interruptions.

The Homelite UT10942D also boasts a durable construction, designed to withstand the rigors of frequent use. Its heavy-duty parts are built to last while still being lightweight, reducing fatigue during extended sessions. Furthermore, the inclusion of an adjustable cutting head enhances versatility, allowing users to switch between trimming and edging functions easily.

For added convenience, the trimmer comes with an anti-vibration feature that decreases hand fatigue, making it comfortable to operate for prolonged periods. Safety features, including a guard to protect the user from debris and a secure grip handle, are also part of the design, ensuring a safer cutting experience.

In summary, the Homelite UT10942D is a reliable and efficient string trimmer that combines power and ease of use. Its innovative technologies and thoughtful features make it a popular choice among homeowners and professionals alike, providing a truly effective tool for lawn care and maintenance. Whether for maintaining a small garden or taking care of larger landscapes, the UT10942D is equipped to handle the challenge, delivering precise results every time.
Top Page Image Contents