START-UP Checklist

Guardian Technologies 005336-1, 005337-1 START-UP Checklist, Preparation for START-UP

Standby Generator Sets

Installation

•Battery charger connection to 120 VAC.

•Communication wires connected between transfer switch and generator (HTS only).

•Unit secured to pad.

Before working on the generator, ensure the fol- lowing:

•The AUTO/OFF/MANUAL switch is in the OFF position.

•The 120VAC supply to the battery charger is switched OFF.

PREPARATION FOR START-UP

•Ensure that the 120VAC circuit breaker to the bat- tery charger is open.

•Remove the fuse from the the control panel. For the H-100 and R-series: Open the front door of the control box and remove the 15 Amp ATO fuse in the lower left-hand corner of the control box.

•Connect the battery cables to the battery. Attach negative battery cable last.

•Close the 120VAC circuit breaker to the battery charger.

•Measure the voltage at the battery before and after the charger is turned on.

•Verify all AC electrical connections are tight at the circuit breaker and transfer switch.

•Visually inspect entire area looking for loose paper, plastic wrappings, leaves, etc.

•Check all hoses clamps fittings for leaks or dam- age.

•Check all electrical plugs throughout the genera- tor. Ensure each plug is seated correctly and fully inserted into its receptacle.

•Verify the AUTO/OFF/MANUAL switch is in OFF position.

•Open the valve to the engine fuel line.

•Bleed the fuel system of air. (necessary for long fuel lines).

•Open the generator main line circuit breaker.

•Connect a manometer to the gas line and record the static pressure. It must be as listed in the Specifications.

•Insert the fuse into the control panel.

•Move the AUTO/OFF/MANUAL switch to the MAN- UAL position. The engine should now crank and start.

•Check voltage at the generator terminals.

•For 3-phase units, check phase rotation at the transfer switch terminals. The generator phase rotation must match the utility phase rotation.

•Check for coolant, fuel, oil, and exhaust leaks.

•Close the generators main line circuit breaker.

•Turn the generator set off.

•Connect the UTILITY supply to the transfer switch.

•Set the AUTO/OFF/MANUAL switch to AUTO.

•Disconnect utility power before the transfer switch.

Engine should start, transfer to load.

Run at least 15 minutes on generator power. Make certain all 3-phase loads are functioning correctly (correct phase rotation).

•Reconnect Utility power

Transfer switch will transfer back to Utility and engine will shut down within the given time parameters set up for the specific transfer switch and controller.

•Install all covers, access plates and door panels.

•Put the Owners Manual in a safe and accessible place.

•Make certain the AUTO/OFF/MANUAL switch is in the AUTO position.

START-UP INSPECTION

When a start-up is performed by an Authorized Service Dealer, a standard three-part form titled “Start-up Inspection for Standby Power Systems” (part no. 067377), should be completed by the instal- lation technician or engineer. See page 1-3 for infor- mation on locating the nearest Authorized Service Dealer. The installer should complete the form and disseminate copies as follows:

•White copy: Mail to Generac Warranty Department, P.O. Box 340, 211 Murphy Dr., Eagle, WI 53119- 2062.

•Pink Copy: For service file of installing dealer.

•Yellow Copy: For the customer’s records.

01/07 D .Rev Install001

8-2

005336-1, 005337-1 specifications

Guardian Technologies has evolved as a leader in indoor air quality solutions with its innovative lineup of air purifiers, particularly the notable models 005336-1 and 005337-1. These devices are designed to tackle common air contaminants, enhancing the overall air quality in residential and commercial settings.

The model 005336-1 features a state-of-the-art 3-in-1 air purification system, integrating a pre-filter, activated charcoal filter, and a true HEPA filter. This powerful combination ensures the removal of a wide array of pollutants, including dust, pet dander, smoke, and even certain bacteria and viruses. The true HEPA filter captures 99.97% of particles as small as 0.3 microns, making it an excellent choice for allergy sufferers and individuals sensitive to airborne particles.

On the other hand, the 005337-1 model advances air purification further with enhanced smart features. It is equipped with a built-in air quality sensor that monitors real-time air quality and adjusts the fan speed accordingly. This not only promotes energy efficiency but also ensures an optimal environment based on immediate air quality needs.

Both models incorporate Guardian Technologies’ unique UV-C light technology. This additional feature works to reduce airborne germs and bacteria, further improving the healthiness of the air you breathe. The UV-C technology, combined with the HEPA filtration system, provides a comprehensive approach to cleaning indoor air, making these models perfect for households with pets, children, or individuals with allergies.

Another standout characteristic of both air purifiers is their user-friendly design. They come equipped with adjustable fan speeds, a filter replacement indicator, and a quiet operation mode that makes them suitable for use in bedrooms or home offices. Moreover, their modern aesthetics fit seamlessly into various home decors, ensuring functionality without compromising style.

In summary, Guardian Technologies’ 005336-1 and 005337-1 air purifiers offer a sophisticated blend of effective air purification technology, user-friendly features, and smart capabilities. They represent a commitment to improving indoor air quality and promoting a healthier living environment for all. This combination of efficiency and innovation positions Guardian Technologies at the forefront of air purification solutions.