Assembly

Tank

Wrap

Illustration 2

Push

illustration 3

Tank Stand (MT-200 series only)

1.Insert tank support strap into openings in tank stand as shown. See Figure A.

2.On the underside of the tank stand, loosen the two hex nuts located on the screws which extend from the sides of the base plate. Place the slots at the ends of the tank support strap over the screws and secure by tightening the two nuts. See Figure B.

PowerTrap (MT-200 & MT-300 series)

Tank Support	Tank Stand
Strap

Openings

Figure A

Base Plate Tank Strap

Screw & Nut

(2 places)

Figure B

Connect Propane Regulator

1 . Remove the plastic dust cover from your propane tank valve.

2 . Screw the propane regulator coupling located on the end of the propane hose onto the tank valve by turning the black threaded coupling clockwise until tight. Hand tighten only. See Illustration 4.

Note: Gas will not ﬂow unless connection is tight.

Tighten by hand only. Using a wrench or other tool could damage the regulator coupling and could cause a gas leak.

Illustration. 4

WARNING

Check for gas leaks by wetting the connec- tions with a solution of soap and water and

1.Insert one end of the post into the post opening at the front of the tank stand. Insert opposite end of post into the post opening located at the bottom of the Flowtron Mosquito PowerTrap®. Align unit in relation to the tank stand.

See Illustration 2.

Place a 20 lb. tank on the tank stand and install tank wrap around the tank.

2.Install catch tray by ﬁrst inserting the rear of the tray into the housing.

Then push in upper part of the latch and raise front of catch tray into place.S e e

Illustration 3.

Tank

Cap

Tank

Strap

Post

Tank Stand

watching for bubbles. If bubbles form or if a bubble grows larger, there is a leak and connection must be tightened.

WARNING

Check for gas leaks every time you disconnect and reconnect a gas ﬁtting.

Be sure there are no sparks or open ﬂame in the area when you check for leaks.

Do not use a liquid propane tank with a damaged valve. Have dented or rusty propane tanks checked by your propane supplier.

Only use regulator supplied with your Flowtron PowerTrap.

3.Place tank cap on top of tank.

4 . ( M T-300 series only )

Move your unit to the

3 . Position and screw power

pack to either an outside or inside wall adjacent to

a electrical outlet (screws not provided). Run the low

voltage wire either above or below ground from the power pack to the unit. plug the low voltage wire into the power cord connector located at the bottom of the Flowtron Mosquito PowerTrap®. Plug the power pack into the electrical outlet.

desired location in your

yard. Remove catch tray

and grasp housing as

shown .

See trap “Placement”

instructions on pg. 4.

Page 5

MT-200 Series, MT-300 Series specifications

Flowtron Outdoor Products, a leader in insect control solutions, offers the MT-300 Series and MT-200 Series, designed to enhance outdoor living spaces by effectively reducing pests. These versatile units are perfect for patios, decks, and gardens, ensuring a comfortable and enjoyable experience without the annoyance of pesky insects.

The MT-300 Series is equipped with a powerful 120-watt bulb that emits ultraviolet light, attracting a wide range of flying insects, including mosquitoes, flies, and moths. The durable construction of the MT-300 ensures long-lasting performance even in harsh outdoor conditions. One of the standout features of this model is its patented, non-clogging killing grid, which ensures efficient pest elimination without maintenance hassles. The design also allows for easy bulb replacement, ensuring that homeowners can keep their spaces free from pests throughout the season.

In contrast, the MT-200 Series offers a compact design suitable for smaller outdoor areas, such as balconies or smaller yards. This series uses a 40-watt ultraviolet bulb to effectively draw in insects while maintaining low energy consumption. The MT-200 is designed with user-friendliness in mind, featuring a simple plug-and-play operation. It is lightweight and portable, allowing users to easily relocate it based on their needs. Like the MT-300, the MT-200 also includes a non-clogging grid, ensuring reliable insect control.

Both series feature built-in safety features, including an outer protective mesh, preventing accidental contact with the electric grid. This makes them safe for homes with children and pets. Additionally, these units are environmentally friendly, using no harmful chemicals or sprays, making them suitable for organic gardening and eco-conscious consumers.

Overall, the Flowtron MT-300 and MT-200 Series are excellent choices for anyone looking to reduce outdoor flying insects. With their robust construction, energy-efficient operation, and effective pest control capabilities, they stand out as must-have outdoor products for the warmer months. By employing advanced technologies and user-centric designs, Flowtron continues to solidify its position as a trusted name in outdoor pest management. Enjoy your outdoor spaces with ease and confidence, free from the distraction of unwanted insects.