Venting requirements, Dimensional diagram | Faber 1200 CFM specification

Venting requirements

Determine which ducting method is best for your application. Duct system can extend either through the wall or the roof. Locate the remote blower so that the length of the duct system and the number of elbows is kept to a minimum to provide efﬁcient performance. Where possible, remote blower should

be centered between wall studs or roof rafters. The size of the duct system should be uniform. Do not install two elbows together.

Use duct tape to seal all joints in the duct system. Use caulking to seal remote wall or ﬂoor opening around the cap. Flexible duct is not recommended. It creates back pressure/air turbulence and greatly reduces performance. Make sure there is proper

clearance within the wall or ﬂoor for exhaust duct before making cutouts. Avoid pipes, wires, or other duct systems that may be running through the wall. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be constructed.

The remote blower carton contains a duct collar plate.

•The duct collar plate attaches to the front of downdraft duct system plenums so that the 10" (25.4 cm) round duct can be attached to the downdraft duct system.

Make sure that there is enough space for any vent transitions that may be needed between the remote blower and the connecting vent system. For optimum performance, locate any necessary vent transitions nearest to the rangehood or downdraft that will be used with this power system. This remote blower requires a separate U.L./CSA approved wiring cable that

should be installed at the same time the vent system is being installed.

Dimensional diagram

MAKE SURE THAT THE DISCHARGE END OF THE REMOTE BLOWER FACES AWAY FROM THE DIRECTION OF PREVAILING WINDS.

!WARNING

You can be killed or seriously injured if you don’t follow instructions.

Excessive Weight Hazard

Use two or more people to move and install remote blower.

Failure to do so can result in back or other injury.

Install this side of the fan facing an unoccupied space.

Maximum length of ductwork

55 feet for 10" round ductwork - count 90° elbows as 5 feet and 45° elbows as 3 feet.

Duct length is given as a general reference only. For a longer

duct run, or smaller duct system, contact a qualiﬁed and trained duct installer. Check with local codes for makeup air requirements, if any. It is recommended that you use round duct instead of rectangular duct, especially if elbows are

required. If rectangular duct is required, if should be transitioned to 10" (25.4 cm) round duct as soon as possible.

For best performance, use no more than three 90° elbows.

If more than one elbow is used, make sure that there is a minimum of 24 inches of straight duct between any two elbows. Do not install two elbows together.

Begin the installation

1.Discard any cardboard packaging from the blower wheel.

2.Remove wiring box cover and screws.

3.Attach an appropriate U.L./CSA-listed strain relief in the knockout.

Note: For most installations, it is recommended that the strain relief be installed so that it can be tightened from inside the remote blower housing.

4.Reattach the wiring box cover loosely. It will be removed again later.

Follow the instructions on the next page for your type of installation

Version 05/06 - Page 2

1200 CFM specifications

The Faber 1200 CFM range hood is a powerful appliance designed to enhance your kitchen experience by efficiently removing smoke, steam, and odors generated during cooking. With its impressive airflow capacity of 1200 cubic feet per minute, it is ideal for larger kitchen spaces and high-heat cooking methods.

One of the standout features of the Faber 1200 CFM range hood is its advanced ventilation technology. This hood employs a multi-layered filtration system that captures grease and other particulates, ensuring a cleaner kitchen environment. The filters are typically constructed of stainless steel, making them durable and easy to maintain. Many models also come with dishwasher-safe filters, allowing for effortless cleaning and consistent performance.

In terms of design, the Faber 1200 CFM range hood embodies a modern aesthetic that suits a variety of kitchen styles. Available in different finishes such as stainless steel, chrome, and black, it can seamlessly integrate into your kitchen decor. Many models boast a sleek, low-profile design that maximizes both form and function without overwhelming the space.

Another significant characteristic of the Faber 1200 CFM is its noise performance. Designed with sound insulation technology, this range hood operates quietly, allowing you to enjoy a peaceful cooking experience. It offers multiple speed settings, enabling you to adjust the ventilation power based on your cooking needs while reducing noise levels.

Faber also focuses on user convenience with features such as LED lighting, which illuminates your cooking area without generating excessive heat. These lights are not just energy-efficient but also enhance visibility during food preparation. Additionally, some models come equipped with intuitive electronic controls, including touch-sensitive buttons, making it easy to operate the hood.

Safety is paramount, and the Faber 1200 CFM range hood often includes features like a delay shut-off timer, which allows the unit to run for a predetermined time before turning off automatically, ensuring all cooking byproducts are adequately vented.

In summary, the Faber 1200 CFM range hood combines efficiency, style, and advanced technology, making it an excellent choice for anyone looking to upgrade their kitchen ventilation system. With its powerful airflow, easy maintenance, and user-friendly features, it stands out as a reliable partner in any culinary endeavor.