Installation Instructions Composite Back Panel

EDFPVR217RC

INSTALLATION INSTRUCTIONS

COMPOSITE BACK PANEL

1.Wall should already be framed for the fountain using the positioning dimensions shown in Fig. 2. Shown dimensions pertain to installation location (framing must support up to 150 lbs. weight).

2.Install rough-in plumbing as shown in Fig. 2. Run supply water inlet line and connect to a

service stop (not provided). Turn on supply water and flush thoroughly. Close water supply.

3.Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back panel and wall using (4) 5/16" bolts and washers (not provided). Bolts should be long enough to securely fasten the fountain to the wall. Tighten securely, but do not over tighten. Over tightening will crack the Marblyte Fountain.

4.Remove elbow from end of p-trap(item 1) and attach it to drain tube. Re-attach elbow to p-trap and cut waste tube to required length using plumbing hadware and trap as guide.

5.Make water supply connections from service stop to the fountain strainer (Item 16) by inserting the water inlet line into the inlet side of strainer until it reaches a positive stop about 3/4", (See Figure 6, Page 7). Turn on water supply and check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER

AS DAMAGE TO THE O-RINGS MAY RESULT.

6.These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of connecting these products to supply line pressure lower than 20 PSIG or higher than 105 PSIG is not covered by warranty.

7.Check stream height from bubbler. Stream height is factory set at 45-50 PSI. If supply pressure varies greatly from this, adjust the screw on regulator item 14 by using a small screwdriver through the small hole in the push button item 8 (See Fig.3). Clockwise adjustment will raise stream height and counter- clockwise adjustment will lower stream height. For best adjustment stream height should be approxi- mately 1-1/2" (38mm) above the bubbler.

8.Replace bottom access panel to fountain basin using screws provided. Tighten securely.

Care and Maintenance of ELKAY Composite Fountains

Elkay Composite fountains provide an exremely durable, nonporous surface which resists staining. Care is very simple. Routine cleaning with a soft sponge or cloth, or with water or non-abrasive aerosol foam cleaner, is all that is normally needed to give many years of trouble free service. Cleaners left standing on the fountain surface can dull the surface finish. Be certain to rinse all cleaning agents completely and polish with a soft cloth.

Harsh abrasive cleaners are not required and should not be used.

Mild abrasives such as liquid automotive cleaning compound or baking soda paste will remove simple scratches and stains. Cigarette burns can normally be removed without noticeable effect. Deeper scratches or gouges can be corrected with fine grit sandpaper (240 grit then 400 grit) or a green Scotchbrite pad.

To maintain or regain luster and make cleaning easier, periodic applications of automobile wax or like products will keep the finish looking like new.

PAGE 3

98409C (Rev. B - 9/08)

EDFPVR217RC specifications

The Elkay EDFPVR217RC is an advanced drinking water fountain designed to meet the diverse needs of various environments, including schools, office buildings, and public spaces. This sophisticated model combines modern design with innovative technology, making it a perfect choice for those looking for both functionality and aesthetics.

One of the key features of the EDFPVR217RC is its integrated water bottle filling station. This allows users to conveniently refill their reusable water bottles, promoting sustainability and reducing plastic waste. The filling station is equipped with a self-closing valve, which enhances functionality and safety by preventing spills and overflows.

The Elkay EDFPVR217RC also boasts a high-efficiency cooling system. This system ensures that the water served is refreshingly cool, making it appealing for users, especially in warmer climates. The efficient cooling mechanism is designed to conserve energy, minimizing the environmental impact of the unit while maintaining excellent performance.

Another noteworthy characteristic of this drinking fountain is its electronic water control system. This technology allows for touchless operation, ensuring a hygienic experience for users. The touchless feature reduces the spread of germs, which is particularly important in high-traffic areas where cleanliness is paramount. The EDFPVR217RC also includes antibacterial surfaces, further enhancing its suitability in contemporary hygiene-focused settings.

The Elkay EDFPVR217RC is designed with durability in mind. Constructed from high-quality materials, this model can withstand the rigors of daily use. Its robust design is backed by rigorous testing, ensuring reliability over time. The unit is also easy to maintain, featuring accessible components for quick servicing and repair.

In terms of design, the EDFPVR217RC offers a sleek and modern appearance that can effortlessly blend into various architectural styles. Available in multiple finishes, it allows for customization to suit specific décor needs.

In summary, the Elkay EDFPVR217RC stands out due to its innovative features, including a convenient water bottle filling station, touchless operation, and energy-efficient cooling. Its emphasis on hygiene, durability, and modern design makes it an ideal choice for anyone looking to enhance their hydration options in both public and private spaces. This drinking water fountain represents a perfect balance of functionality, safety, and aesthetic appeal, making it a valuable addition to any environment.