Trouble Shoot ING, Timer Play, Filter Switch

ENGLISH	power socket and the timer’s power cord to power
	TIMER PLAY
	This unit can perform timer play by cooperating with
	your audio timer.
	Connect this unit’s power cord to the audio timer’s
	outlet.
	* For connection to audio timer and it’s operation,
	please refer to the instruction manual of your audio

timer.

Audio Timer

AC IN

Setting method of Timer Play

qPress POWER switch to turn ON the power.

wInsert the disc to be played.

*In timer play mode, tracks are played normally.

eSet the audio timer.

FILTER SWITCH

FILTER

STAN- CUS-

DARD TOM

AC IN

AUDIO OUT

FILTER DIGITAL AUDIO OUT

REMOTE CONTROL

OPT. COAX.

L	R	STAN-	CUS-
		DARD	TOM	EXT. INT.
				OUT

Super Audio CDs have a wide playback frequency band of 100 kHz that is beyond the audible range: this means that their signals contain ultra-high-range components that conventional CDs do not have. A conventional amplifier is often not built to reproduce signals containing these components, and when Super Audio CD signals are output in their original state, noise may be generated, the amplifier’s protection circuits may be activated and/or the speakers may be damaged.

To prevent this sort of trouble from occurring, the unit incorporates a filter (STANDARD) for attenuating the ultra-high-range components, and the filter can be set STANDARD or CUSTOM using a switch on the rear panel. (This switch is set to STANDARD when the unit is shipped from the manufacturing plant.)

When the unit is to be connected with a next- generation amplifier that supports Super Audio CDs and set the switch to CUSTOM for use. This will ensure play with a wider frequency range.

*Use the switch at the STANDARD position if the unit is to be used with a regular amplifier. Otherwise, the amplifier and/or speakers may be damaged.

*Even when the unit has been connected with an amplifier that supports Super Audio CDs, change the switch to the STANDARD position when recording Super Audio CD sound on a tape deck, for instance.

*Turn the power off before setting this switch. Setting the switch during play may cause noise to be generated.

TROUBLE SHOOT-

ING

If you think a malfunction has occurred, first check the points listed below. The problem is likely to have been caused by a simple operational error or a connection problem. If the problem cannot be corrected even after carrying out the following checks, consult your dealer or nearest Marantz sales office or service counter.

•The disc fails to rotate.

1.Is the mains lead plugged in properly?

2.Is the POWER switch ON?

3.Is the disc placed in the correct position on the disc tray?

4.Is the disc placed properly with the label side facing up?

5.Is the disc dirty?

6.Is the disc scratched?

7.Is the disc warped?

•The disc is rotating but no sound is heard.

1.Are the amplifier and speakers connected properly?

2.Is the amplifier switch ON?

3.Is the amplifier’s function or selector switch set to “CD” or “AUX” or such (to whatever you have connected this unit to)?

4.Is the amplifier’s volume control set at the minimum level?

•The disc stops in mid-operation.

The sound drops out or noise is heard.

1.Is the disc dirty?

2.Is the disc scratched?

3.Is the disc warped?

*In the case of a CD-R or CD-RW disc, this problem may occur when the conditions under which its data was originally written were substandard or when the quality of the disc itself is poor.

*This condition may occur in Mixed-Mode CDs, CD Extra, and other discs that have CDDA format mixed with other data.

Noise may also be heard momentarily when skipping tracks.

•Remote control operation is not possible.

1.Is the transmitter of the remote control unit (RC8400SA) pointed correctly at the remote sensor on the front of the player (this unit)?

Or is there an obstruction between the transmitter and the remote sensor?

2.Are the batteries in the remote control unit exhausted?

3.Is there another strong light (from a window, etc.) striking the Super Audio CD player’s remote sensor?

•A Super Audio CD cannot be played.

1.Is the disc scratched, dirty or warped?

2.Is the amplifier’s input selector set to digital?

*Digital audio signal will not be output when a Super Audio CD is played.

3.Is the disc a Super Audio CD multi-channel only disc? (This unit does not support Super Audio CD multi-channel.)

•A CD-R/CD-RW disc cannot be played.

1.Is the disc placed upside down?

2.Is the disc contains properly written TOC?

3.Is the recorded information in an audio (CD-DA) format?

•A specific CD cannot be played

Copy control CDs (CDs with copy guard) are special discs that do not comply with current CD standards. Marantz cannot guarantee the ability to play such discs on your CD player.

When normal CDs can be played without a problem and problems occur only when playing these special discs, it is not a problem with this unit.

Please ask the seller of the copy control CD for detailed information regarding copy control CDs.

•The unit makes a clicking sound when the tray closes

This is the adhesion click of the clamper for securing the disc. This does not cause any problem in using the unit.

•While the disc is spinning, a spinning sound is heard or a slight vibration occur.

Depending on the disc, a spinning sound may occur or the unit may vibrate slightly due to disc eccentricity or such. This is not a problem with this unit.

SA8400 specifications

The Marantz SA8400 is a high-performance SACD player that exemplifies the brand's commitment to audio excellence and innovation. Launched as part of Marantz's extensive line of advanced audio components, the SA8400 offers music enthusiasts an exceptional listening experience, particularly in high-resolution formats.

One of the standout features of the SA8400 is its playback compatibility with Super Audio CDs (SACDs), standard CDs, and CD-R/RW discs. This versatility allows users to enjoy a comprehensive range of media without sacrificing audio fidelity. The player supports both stereo and multi-channel SACD formats, enabling an immersive listening experience that captures the essence of studio-quality sound.

At the heart of the SA8400 is Marantz's advanced Delta-Sigma digital-to-analog converter (DAC) technology. This cutting-edge DAC design significantly enhances audio performance by minimizing digital noise and distortion. The result is a clear, detailed, and dynamic sound reproduction that retains the richness and warmth of analog recordings while benefiting from the precision of digital processing.

The SA8400 also features a robust build quality, incorporating a heavy-duty chassis that minimizes vibrations, isolating the mechanisms from external interference. The attention to detail in the construction ensures that the audio components remain stable, even during intense playback sessions. The player is designed with a high-quality transport mechanism that further supports consistent playback performance over time.

Additionally, the Marantz SA8400 includes a range of connectivity options to enhance its usability. These include both balanced XLR and unbalanced RCA outputs, allowing seamless integration into various audio systems. The player also features a dedicated headphone output, making it convenient for personal listening.

One of the more notable technologies in the SA8400 is the inclusion of Marantz's "HDAM" (Hyper Dynamic Amplification Module), which contributes to superior sound quality by providing improved fast transient response and greater dynamic range. This technology is crucial in delivering the nuanced soundstage that audiophiles seek.

Overall, the Marantz SA8400 is a sophisticated SACD player that caters to those who seek high-fidelity audio. With its impressive technological features, versatile playback capabilities, and robust construction, it stands out as a premier choice for serious music lovers looking to elevate their listening experience.

TIMER PLAY