Storage, Maintenance, Replacement Parts

OPERATION STORAGE MAINTENANCE REPLACEMENT PARTS

OPERATION

Continued

9.Push knob in and quickly press IGNITOR button (see Figure 14). Repeat until heater is lit. This can be easily done by placing index finger in access hole on left of control cover and push- ing ignitor with thumb (see Figure 14).

10.Continue holding knob in for approximately 30 seconds. Heater should remain lit in the LOW heat setting.

11.For more heat, press knob and rotate counterclockwise to HIGH setting.

12.If RELIGHTING, wait 5 minutes for heater to cool and gas to clear, then follow steps 4 through 11.

Control Knob

Access

Hole in

Control Box

Piezo

Ignitor

Figure 14 - Piezo and Control Knob Locations

SHUTDOWN INSTRUCTIONS

1.Press control knob and rotate clockwise to OFF position.

2.Close propane/LP cylinder valve (rotate knob clockwise).

STORAGE

CAUTION: Disconnect heater from propane/LP supply cylinder.

1.Do not store heater while attached to propane/LP cylinder. Close cylinder valve. Remove the hose/regulator assembly from the propane/LP cylinder by turning the fuel gas connector nut clockwise.

2.Store propane/LP cylinder in safe manner. Refer to Chapter 5 of Standard for Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58. Follow all local codes. Always store propane/LP cylinders outdoors. Never store propane/LP cyl- inder in an enclosed area.

3.Store in a dry, clean, and safe place.

MAINTENANCE

WARNING: Never attempt to service heater while it is connected to propane/LP supply, operating, or hot. Severe burns can occur. Any guard or other protective device removed for servicing must be replaced prior to operating the heater.

1.Keep heater clean. Remove any debris from ventilation open- ings (see Figures 12 and 13, page 6).

2.Inspect heater before each use. Check connections for leaks. Ap- ply mixture of liquid soap and water to connections. Bubbles form- ing show a leak that must be corrected. Correct all leaks at once.

3.Inspect hose/regulator assembly before each use. If hose is highly worn or cut, replace it immediately.At least annually, remove hose/ regulator assembly from heater to inspect entire length of hose.

4.Spiders and insects can create a dangerous condition that may damage heater or make it unsafe. Keep burner area clean of all spiders, webs, or insects.

5.Have heater inspected yearly by a qualified service person.

REPLACEMENT PARTS

WARNING: Use only original replacementparts. This heater must use design-specific parts. Do not substitute or use generic parts. Improper replacement parts could cause serious or fatal injuries. This will also protect your warranty coverage for parts replaced under warranty.

PARTS UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), either contact your nearest Parts Cen- tral or call DESA International’s Technical Service Department at 1-866-672-6040.

When calling DESA International, have ready

•your name

•your address

•model and serial numbers of your heater

•purchase date

•how heater was malfunctioning

In most cases, we will ask you to return the part to the factory.

PARTS NOT UNDER WARRANTY

Contact authorized dealers of this product. If they can’t supply original replacement part(s), either contact your nearest Parts Central listed in the Authorized Service Center booklet supplied with heater or call DESA International at 1-866-672-6040 for referral information.

When calling DESA International, have ready

•model number of your heater

•the replacement part number

For morevisit www..com

107396

28BN specifications

Desa 28BN is an innovative residential community that redefines modern living with its unique blend of cutting-edge technology and sustainable design. Located in a serene environment, this community is designed to foster a sense of belonging while offering state-of-the-art amenities and features that cater to the needs of its residents.

One of the primary features of Desa 28BN is its commitment to sustainability. The community is built with eco-friendly materials and design principles that minimize environmental impact. Green roofs, rainwater harvesting systems, and solar panels are integrated into the architecture, ensuring that the community remains energy-efficient and environmentally friendly. This conscious approach to construction not only reduces the carbon footprint but also promotes a healthier living environment.

In terms of technology, Desa 28BN is equipped with smart home automation systems that enhance the living experience. Residents can control lighting, heating, and security systems through their smartphones, allowing for convenience and peace of mind. The community is also equipped with high-speed internet connectivity, enabling residents to stay connected and work remotely with ease.

Desa 28BN places a strong emphasis on community engagement and social interaction. The layout of the neighborhood encourages walkability, with pedestrian-friendly pathways, parks, and communal spaces designed for gatherings and recreational activities. This fosters a sense of unity among residents, creating a vibrant and welcoming atmosphere.

Security is a top priority in Desa 28BN. The community features 24/7 surveillance systems, gated access, and trained security personnel to ensure the safety of all residents. This focus on security allows families to feel safe and comfortable within their homes and the surrounding environment.

Additionally, the community offers a range of amenities including fitness centers, swimming pools, and children’s play areas. These facilities encourage an active lifestyle and provide opportunities for social interactions among residents.

In conclusion, Desa 28BN represents a forward-thinking approach to residential living, blending sustainability, technology, and community engagement. Its thoughtful design and commitment to resident well-being make it an exemplary model of modern housing, catering to the aspirations of today’s families while keeping the future in mind.