DeWalt DWE46101 manual Attaching Side Handle fig, Mounting and Removing Mortar Raking Shroud fig

ENGLISH

Attaching Side Handle (fig. 1)

WARNING: Before using the tool, check that the handle is tightened securely.

Screw the side handle (c) tightly into one of the holes

(p) on either side of the gear case.

Mounting and Removing Mortar Raking Shroud (fig. 3)

NOTE: The supplied mortar raking shroud is only recommended for use with the DWE46101 heavy- duty mortar raking motor.

1.Open the clamp lever (n) on the tuckpoint shroud and align the tabs (q) on the tuckpoint shroud with the slots (r) on the grinder gear case.

2.With the clamp lever open, rotate the shroud into the desired working position. The shroud should be positioned between the spindle and the operator to provide optimum efficiency.

3.Close the clamp lever (n) to secure the tuckpoint shroud on the gear case. Do not operate the grinder with a loose tuckpoint shroud or the clamp lever in open position.

4.To remove the tuckpoint shroud, open the clamp lever, rotate the tuckpoint shroud to align the slots and tabs and pull up on the tuckpoint shroud.

NOTE: The tuckpoint shroud is pre-adjusted to the diameter of the gear case hub at the factory. If, after a period of time, the tuckpoint shroud becomes loose, tighten the clamp adjusting screw (i) with clamp lever in the closed position.

NOTICE: Do not tighten the clamp adjusting screw with the clamp lever in open position. Undetectable damage to the tuckpoint shroud or the mounting hub may result.

NOTICE: If tuckpoint shroud cannot be tightened by the clamp adjusting clamp, do not use tool. Take the tool and tuckpoint shroud to a service center to repair or replace the tuckpoint shroud.

Fitting and Removing a Cutting Disc (fig. 1, 4)

WARNING: Do not use a damaged disc.

1.With shroud installed, place the tool on a table, spindle up.

2.Fit the backing flange (d) correctly onto the spindle (b) (fig. 4).

3.Rotate open the cornering door (m) and place the cutting disc (u) on the backing flange (d).

4.Screw the threaded clamp nut (e) onto the spindle (b).

5.Press the spindle lock button (a) and rotate the spindle (b) until it locks in position.

6.Tighten the threaded clamp nut (e) with the two- pin spanner supplied.

7.Release the spindle lock.

8.Close and secure the cornering door (m) by tightening the cornering door locking lever (l).

9.To remove the disc, loosen the threaded clamp nut (e) with the two-pin spanner.

Mortar Raking Shroud (fig. 6)

WARNING: Only Type 1 diamond wheels shall be used with tuck- point shroud. Do not cut metal. Do not use with bonded abrasive wheels.

Follow the Fitting and Removing a Cutting Disc instructions and mount the grinding disc.

It may be necessary to open the cornering door to install 125 mm tuckpointing wheels, refer to

Cornering Door Application.

DEPTH OF CUT ADJUSTMENT (FIG. 5)

1.Loosen the depth of cut shoe locking knob (k).

2.Slide the depth of cut shoe (j) to the desired position.

3.Tighten depth of cut shoe locking knob.

CORNER DOOR APPLICATION (FIG. 6)

WARNING: To reduce the risk of injury, ALWAYS turn the tool off and disconnect the tool from the power source before making any adjustments or removing or installing attachments or accessories. This applies to both the grinder and the dust extractor vacuum. Such preventative safety measures reduce the risk of starting the tool accidentally.

WARNING: Risk of personal injury. The corner door should only be opened for cutting inside corners. Keep hands and body away from cutting area at all times. Ensure corner door is closed in all other applications.

This feature allows the cutting of an inside corner.

1.Ensure the tool is off and wheel has come to a complete stop.

39