Bush Hog 5145 manual Adjusting Bucket Level Indicator, Lift and Bucket Cylinder Reassembly

Page 97

MAINTENANCE

Lift and Bucket Cylinder Reassembly

Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly.

1.Place rod seal (3) into groove inside cylinder head.

Note: Lips of seal (3) must be face inward and seal must be firmly seated in groove.

2.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head (5). Install wear ring (4) inside other end of head (5).

3.Place o-ring (7) with back-up washer (6) in groove on outside of head. Back-up washer must be on rod side.

4.Remove sharp edges on outer edge of the threaded end of shaft (1). Lubricate wiper seal (2) and rod seal

(3) in head and carefully slide head onto shaft.

5.Place o-ring (10), piston seal (11) and piston wear ring (8) in grooves on outside of piston (9). Note: For easier installation, place piston seal (11) in 120°F water to warm seal.

6.Slide piston (9) onto threaded end of shaft and install lock nut (12). Tighten lock nut to 100 lbs.

7.Lubricate piston wear ring (8) and piston seal (11) on piston, o-ring (7) and backup washer (6) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube (13).

8.Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.

Note: If cylinder has a countersunk hole, hook end of retaining wire into hole and turn cylinder head 1-1/2 turns to secure wire. End of hook may need to be ground to fit in countersunk hole.

Adjusting Bucket Level Indicator

With various tractor tire options or attachments, it may be necessary to adjust bucket level indicator bracket up or down on bucket cylinder tube. Tractor must be on level surface with attachment flat on surface. Loosen u-bolt to adjust. Off-set on bucket level indicator rod should be in slotted hole when attachment is level.

5145 01/11

Maintenance Section 5-7

© 2011 Alamo Group Inc.

MAINTENANCE

Page 96 Page 98
Image 97
Page 96 Page 98
Contents 5145 To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety5145 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety 5145 01/11 Safety Section SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 5145 01/11 Safety Section See Your Bush HOG Dealer Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Model Name Decal DescriptionD469 5145 01/11 Safety Section Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions Assembly5145 01/11 Assembly Section Proper Rear Ballasting and Wheel Spacing Dismounting Loader Dismounting Loader and Mounting Loader to TractorMounting Loader Attaching Pin on Bucket Mounting Attachment to Loader Mounting and Dismounting AttachmentAssembling Quick Attach Device Detaching Quick Attach DeviceInstalling Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Lighting and SMV Emblem Tractor Ballast Getting On and Off the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Pre-Operation Inspection and Service Loader Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceMount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Implement Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Carrying the Load Lowering the Bucket Dumping the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuidePage Maintenance Section Maintenance 5145 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Lift and Bucket Cylinder Disassembly Cylinder ServiceLift and Bucket Cylinder Reassembly Adjusting Bucket Level IndicatorStorage Maintenance Proper Torque for Fasteners Maintenance Maintenance Page Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

5145 specifications

The Bush Hog 5145 is a versatile and robust rotary cutter designed for heavy-duty use, perfect for maintaining large properties, farms, and fields. This model stands out in the Bush Hog lineup due to its excellent performance, durability, and user-friendly features, making it a popular choice among landowners and landscapers alike.

One of the standout features of the Bush Hog 5145 is its cutting width, which spans an impressive 15 feet. This allows for efficient coverage of large areas in a shorter amount of time, significantly boosting productivity. The cutter is equipped with high-strength steel blades that can easily manage thick brush, tall grass, and tough vegetation, ensuring clean and effective cutting.

The 5145 utilizes a heavy-duty construction, with a robust gearbox and substantial frame designed to withstand rigorous use in challenging environments. This ensures longevity and reliability, even when tackling the toughest vegetation. The heavy-duty drive system provides consistent power transfer, allowing users to tackle various terrains and conditions without compromising performance.

A key technological feature of the Bush Hog 5145 is its ability to be easily adaptable to different tractors, thanks to its adjustable hitch. This makes it compatible with a wide range of vehicles, enhancing its versatility. Additionally, the cutter features an innovative blade brake system that improves safety by quickly stopping the blades when needed, which is particularly useful when transitioning between mowing and transport modes.

The Bush Hog 5145 also emphasizes operator comfort and ease of use. Its ergonomic design allows for intuitive operation, reducing the learning curve for new users. The cutter's lightweight design, combined with its robust construction, enables easy maneuverability while maintaining stability during operation.

Another noteworthy characteristic of the 5145 is its maintenance-friendly design. The cutter is engineered for easy access to vital components, making routine maintenance and inspections straightforward. This contributes to reduced downtime, ensuring that the unit remains operational throughout the cutting season.

In summary, the Bush Hog 5145 rotary cutter blends power, efficiency, and user-centric design, making it a top choice for anyone in need of a reliable solution for large-scale land management. With its impressive cutting width, robust construction, and advanced safety features, it delivers the performance required to keep landscapes in pristine condition.
Top Page Image Contents