Bush Hog 2427, 3227 QT, 2847 manual Section Operating Instructions, General Safety, Operation

Page 14

C. Lower boom until parking stands contact ground.

D. Extend bucket cylinders until cutting edge of bucket is frimly on the ground.

E. Remove pin from mounting bracket.

 

 

Pin

 

Figure 2-8 Mounting Bracket

 

 

 

 

 

 

 

 

 

 

 

F. Loosen nut securing cuffs to loader subframe. Remove pin securing cuff. Remove cuff. (Figure 2-4)

WARNING

USE CAUTION WHEN DISMOUNTING LOADERS EQUIPPED WITH OPTIONAL CONTROL VALVE ON TRACTORS EQUIPPED WITH CANOPY. RAISING LOADER SUBFRAME TOO HIGH CAN PINCH HAND BETWEEN CONTROL HAN- DLE AND CANOPY CAUSING INJURY.

G. With tractor at idle speed, roll bucket back until subframe raises up off rear bracket.

H. With tractor at idle speed, carefully activate boom cylinder until cross tube is free of pressure within front bracket channel. It may be necessary to roll bucket back further to maintain sufficient clear- ance between subframe and rear cross tube.

I. Disconnect hydraulic hoses from tractor quick disconnect couplers.

J. Carefully back tractor out of loader.

NOTE

When dismounting the 2427 QT from certain tractor models, additional subframe height is required to clear the front axle. This may be done by rotating the subframe back by extending the boom cylinders once the cross tube is free of the front channel.

K. Reinstall cuffs to loader subframe and place pin in front mounting bracket for storage.

L. Clean all dirt and debris from loader. Dirt will hold moisture and cause rust.

M. If loader is to be stored for an extended period of time, perform lubrication per paragraph 4-2. Also apply coat of heavy grease to exposed cylinder rods to prevent rusting.

SECTION III

OPERATING INSTRUCTIONS

3-1 GENERAL SAFETY

Only qualified people familiar with this operator’s manual should operate this machine. Operator should wear hard hat, safety glasses, and safety shoes. The operator should read, understand and practice all safety messages shown on the caution, warning and danger decals affixed to the loader to avoid serious injury or death. It is recommended that tractor be equipped with Rollover Protective System (ROPS) and a seat belt be used. Check for ditches, stumps, holes or other obstacles that could upset tractor or damage loader. Always turn off tractor engine, set parking brake, and lower loader to ground before leaving tractor operator’s seat.

3-2 OPERATION

The loader should be operated with the tractor engine running at 1200-1700 rpm. Excessive speeds are dangerous and may cause bucket spillage and unnecessary strain on both the trac- tor and loader.

When operating in temperatures below 30°F (-1°C.), run the tractor engine below 1200 rpm until the oil temperature exceeds 30°F.

A bucket level, indicator rod (Figure 3-1) located on the loader frame can be used to determine bucket angle. Before beginning work, observe the position of indicator rod with bucket flat on ground. Raise boom to several different positions. At each position level bucket, then observe the indicator rod. Once familiar with the indicator rod positions, operation of loader will be easier and more efficient.

The following text and illustrations offer suggested loader and tractor operating techniques.

Figure 3-1

Level

Indicator Rod

13

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Bush HOG Congratulations 2427, 2447, 2847 & 3227 QT This Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Loader Important Safety PrecautionsTractor Safety Precautions Operating the LoaderEMPLOYERS, Employees and Operations Employee Tractor Operating InstructionsSection Introduction and Description Introduction DescriptionTechnical Specifications Mounting Loader Section Loader Mounting and DismountingPreparing Tractor Fixed Pivot PIN Loader Models 2447 QT, 2847 QTParking Stands Installed Dismounting LoaderOperation General SafetySection Operating Instructions Filling the Bucket Lifting the LoadLowering the Bucket Carrying the LoadDumping the Bucket Not this Do this Dump Lower LeverFloat Surface Material Loading from a Bank Operating with Float ControlFloat Loading LOW Trucks or Spreaders from a Pile Peeling and Scraping3RD CUT , 4TH CUT, ETC BackfillingHandling Large Heavy Objects Bale Spear OperationSoil Pile Transporting Fork Lift OperationQuick Hitch Operation Before Each USE Section MaintenanceMaintenance Check List After Each USETroubleshooting Hydraulic System Pressure RequirementsTroubleshooting Procedures Problem Possible Cause Remedy Section V Assembly Mainframe AssemblyLoader Models 2427 QT, 3227 QT Optional Hydraulic Valve Stand Assembly Figure Optional Hydraulic Valve Plumbing Instructions Hose Color CodesBasic Power Beyond Plumbing Instructions Fork Lift Option Bale Spear OptionSide Cutting Edges Optional Bucket Items Assembly Spill Guard AttachmentDigging Teeth Tine TeethSafety Decals Torque Specifications American

2427, 3227 QT, 2847 specifications

The Bush Hog 2847, 3227 QT, and 2427 are leading models in the category of rotary cutters, designed for demanding agricultural and landscaping tasks. Notably recognized for their robust construction and high performance, each model caters to different scales of operation while ensuring efficiency and reliability.

The Bush Hog 2847 is a versatile rotary cutter that offers a cutting width of 84 inches, making it suitable for larger properties and commercial applications. It features a heavy-duty gear drive for enhanced power transfer, which allows for cutting through dense brush and tall grass effortlessly. Equipped with a rugged, reinforced frame, the 2847 stands up to tough working conditions and provides users with a long-lasting tool. Its quick-attach design simplifies mounting and dismounting, improving productivity by minimizing downtime.

Moving to the Bush Hog 3227 QT, often favored for its compact size, this model provides a cutting width of 72 inches. Ideal for both residential and light commercial use, the QT signifies "Quick-Tach," which highlights its easy attachment system. This rotary cutter incorporates a floating top link, allowing for better contour following, ensuring an even cut over undulated terrain. The 3227 is also equipped with heavy-duty blades that enhance cutting efficiency and durability, enabling it to handle a variety of vegetation types with ease.

The Bush Hog 2427 complements the series with a slightly smaller profile, featuring a cutting width of 60 inches. It targets users who need a reliable cutter for smaller jobs or tight spaces. The 2427 is engineered with a solid frame and a unique blade design that ensures optimal cutting performance while preserving the health of the landscape. It also includes a slip clutch or chain driveline option, providing additional protection against shocks from unexpected obstacles during operation.

All three models boast user-friendly technologies such as adjustable cutting heights, ensuring adaptability to varying grass lengths. Their maintenance-friendly designs, with easily accessible grease points and durable materials, contribute to lower upkeep costs over their lifespan. Each rotary cutter in the Bush Hog lineup embodies a blend of power, durability, and innovation, making them essential tools for land management professionals and avid homeowners alike.
Top Page Image Contents