Briggs & Stratton LS401224, LS401216, LS401213 Assembly Instructions, Operating Instructions

Page 9

ASSEMBLY INSTRUCTIONS

NOTE: The following instructions pertain to four SpeeCo log splitters, the 22 ton (LS401221), 25 ton (LS401216), 28 ton (LS401213)

and the 34 ton (LS401224). The four models share most of the component parts. Any differences are noted in the parts list and assembly instructions.

NOTE: This log splitter was partially assembled at the factory. Refer to the drawing and parts list should it become necessary to disassemble the unit for repair or replacement of parts.

STEP 1: Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact your dealer or delivering carrier.

STEP 2: Attach the tongue (3) to the tank/axle (2) as shown in the diagram using the two 1/2 in. NC x 4-1/2 in. hex cap screws (48), 1/2 in. lockwashers (47) and 1/2 in. NC hex nuts (46) from the hardware kit. Tighten. Make sure the ground stand (24) is in the vertical position. NOTE: Flatwashers are included in the hardware kit should it be necessary to use them as spacers. This will eliminate play between the tongue and the tank/tongue mounting plate.

STEP 3: Remove the rubber covering from the two spindles on the tank/axle (2). The wheel bearing cups, bearing cones, grease seals and hub caps are already assembled. Bearing cones have been greased at the factory. Remove the blue, plastic protective covering from the wheel hubs. Mount the wheels (54) to the spindles on the tank/axle (2) using the 3/4 in. light flatwasher (59) and 3/4 in. slotted nut (60) from the hardware kit. There are two types of light flatwashers (59). Use the ones that best allow the wheel to rotate freely after the 3/4 in. slotted nut (60) is tightened down and bearing play is removed. Install the cotter pin (61) and the hub cap (62) from the hardware kit. Repeat step 4 for the other wheel.

STEP 4: Stand the beam (1) up on end. NOTE: At least two people are required to raise the beam for the 28 ton and 34 ton models to insure

safety and prevent injury. Make sure that the beam is stable. Remove the pivot pin (52) and the clip pin (53) from the tank/axle (2). Roll the axle/tongue assembly into position between the two tabs on the beam (1). Slide the pivot pin (52) through the holes and lock in place with the clip pin (53).

STEP 5: Connect the end of the 1/2 in. I.D. x 44 in. (28 & 34 ton models) or 1/2 in. I.D. x 42 in. (22 & 25 ton models) hydraulic hose (21) coming from the fitting (20) on the pump (9) to the fitting (75) on the valve (5) .

STEP 6: Slide one hose clamp (50) on the end of the 3/4 in. I.D. x 37 in. (28 ton and 34 ton models) or 3/4 in. I.D. x 32-1/2 in.

(22 & 25 ton models) hydraulic hose (49) that comes from the fitting on the tank/axle (2). Then connect the hose to the fitting (69) on the valve (5). Tighten the hose clamp.

STEP 7: If the optional fender kit (standard on the 34 ton model) was purchased, attach the fenders (44) to the tank/axle (2) using the 1/4 in. NC x 3/4 in. hex cap screws (43), 1/4 in. flatwashers (42), 1/4 in. lockwashers (41) and 1/4 in. hex nuts (40). Tighten.

OPERATING INSTRUCTIONS

WARNING: Read and thoroughly understand all instructions and safety information before operating this log splitter. Failure to do so may cause serious injury or death. Do not allow anyone to operate this log splitter who has not read this manual. As with all power equipment a log splitter can be dangerous if it is assembled or used improperly. Do not operate this log splitter if you have doubts or questions concerning safe operation. Call our customer service department at 1-800-525-8322 to address these concerns.

Si no entiende ingles, se prefiere que busque alguien que interprete las instrucciones para usted.

IMPORTANT: The engine and hydraulic tank are shipped without oil. See the engine operating and maintenance instructions manual packed with your log splitter for the type of crankcase oil, fuel, etc. The engine manufacturer recommends lead-free gasoline only.

CAUTION: DO NOT START OR RUN THE ENGINE WITHOUT OIL IN THE HYDRAULIC RESERVOIR AND ENGINE.

Page 7

Image 9
Contents LOG Splitters Table of Contents Safety Decals Intended USEPersonal Protective Equipment Page Preparation of the LOG General SafetyWork Area Operation of the LOG SplitterRepair and Maintenance Safety Fire Prevention Hydraulic SafetyImportant Note Towing SafetyOperating Instructions Assembly InstructionsEngine OIL Recommendations Directions for Filling Hydraulic SystemStarting Instructions Operation TowingReference Number Description Required Number Required LS401221, LS401216, LS401213 and LS401224 Log Splitters Model No Serial No Date of Purchase Place of Purchase Maximum Splitting Length Width Shipping WeightForce Engine

LS401213, LS401224, LS401216, LS401221, LS401216, LS401213, LS401224 specifications

Briggs & Stratton has long been a leader in the field of small engine technology, and their latest offerings—LS401216, LS401224, LS401213, and LS401221—are no exception. These models represent a perfect blend of performance, efficiency, and durability, making them ideal solutions for various applications, including lawn care and outdoor equipment.

The LS401216, LS401224, LS401213, and LS401221 are powered by advanced OHV (Overhead Valve) technology, which enhances fuel efficiency and overall engine performance. This design helps to optimize airflow and combustion, resulting in lower emissions and reduced fuel consumption. Consequently, users benefit from longer run times and improved energy efficiency, making these models both eco-friendly and cost-effective.

Each engine model is designed with a robust construction that ensures longevity and reliability. The high-quality materials used in their construction provide excellent resistance to wear and tear, making them suitable for demanding environments. Additionally, the engines feature a lightweight design, making them easy to maneuver and install, without compromising on power.

One of the standout features across these models is the quick-start technology, allowing for easy ignition regardless of temperature or environmental conditions. Users can enjoy hassle-free starts with just a simple pull, enhancing productivity during operation. Furthermore, the integrated air filtration systems enhance engine performance by preventing dirt and debris from entering, which can prolong the engine's lifespan.

The LS401216, LS401224, LS401213, and LS401221 engines also feature customizable options, allowing users to select the horsepower and torque suitable for their specific needs. This versatility ensures that they can be used across a variety of applications, from pushing mowers to pressure washers, making them a popular choice among homeowners and professionals alike.

In addition to performance attributes, these engines are engineered for user comfort and convenience. Features such as vibration dampening and ergonomic designs make operation more comfortable, reducing fatigue during prolonged use. Maintenance is also straightforward, with easy-access components making routine checks and service a breeze.

In summary, the Briggs & Stratton LS401216, LS401224, LS401213, and LS401221 are powerful, efficient, and durable engines catering to diverse outdoor needs. With advanced technology, robust construction, and user-friendly features, these engines exemplify the commitment of Briggs & Stratton to innovation and performance in the small engine sector. Whether for commercial or residential use, these models stand as reliable workhorses in the industry.